When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the country specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera cannot store the country specification information, DTC C1AAA is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AAA | FCM Destination Information Uninitialized | 2 seconds after the power switch is turned on (IG), the forward recognition camera cannot store the vehicle specification information. | ·
CAN communication system ·
Main body ECU (Multiplex network body ECU) ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
This DTC is stored when the forward recognition camera cannot store the country specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.
The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC U0142 is not output | A |
| DTC U0142 is output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 2 seconds or more.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AAA is not output | A |
| DTC C1AAA is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL
Perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 2 seconds or more.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AAA is not output | A |
| DTC C1AAA is output | B |
A
B