Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339648 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The forward recognition camera communicates with the driving support ECU assembly and millimeter wave radar sensor assembly via CAN communication. If there is a communication error with the driving support ECU assembly or millimeter wave radar sensor assembly, the forward recognition camera stores DTC U0235 or U1104.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor 2 seconds after the power switch is turned on (IG), a communication error between the millimeter wave radar sensor assembly and the forward recognition camera is detected for approximately 5 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Forward recognition camera


U1104 Lost Communication with Driving Support ECU 2 seconds after the power switch is turned on (IG), a communication error between the driving support ECU assembly and the forward recognition camera is detected for approximately 5 seconds.
·

CAN communication system

·

Driving support ECU assembly

·

Forward recognition camera



WIRING DIAGRAM

B457894E28
0.521,0.5 2.021,0.74 1.5,0.24 10 false from IG1 NO. 1 Relay 0.76,6.344 3.531,6.625 2.771,0.281 10 false : CAN Communication Line 4.229,1.792 6.229,2.01 2,0.219 10 false Forward Recognition Camera 4.198,3.813 6.115,4.188 1.917,0.375 10 false Millimeter Wave Radar Sensor Assembly 4.156,5.969 6.24,6.167 2.083,0.198 10 false Driving Support ECU Assembly 4.219,1.635 4.625,1.833 0.406,0.198 10 false U15 4.198,3.646 4.625,3.906 0.427,0.26 10 false A91 4.167,5.802 4.542,6.063 0.375,0.26 10 false L205 5.396,0.719 5.844,0.917 0.448,0.198 10 false CANH 5.417,2.844 5.865,3.042 0.448,0.198 10 false CA1P 5.417,4.854 5.865,5.052 0.448,0.198 10 false CA1P 5.417,1.115 5.865,1.313 0.448,0.198 10 false CANL 5.417,3.24 5.865,3.438 0.448,0.198 10 false CA1N 5.417,5.271 5.865,5.469 0.448,0.198 10 false CA1N 4.542,4.667 4.781,4.865 0.24,0.198 10 false B 4.552,2.677 5,2.875 0.448,0.198 10 false IGB 4.552,0.51 5,0.708 0.448,0.198 10 false IGB 4.552,1.24 5,1.438 0.448,0.198 10 false GND 4.542,3.385 4.99,3.583 0.448,0.198 10 false SGND 4.542,5.385 4.99,5.583 0.448,0.198 10 false GND 4.375,0.396 4.573,0.573 0.198,0.177 10 false 7 5.865,0.563 6.063,0.74 0.198,0.177 10 false 6 5.844,0.948 6.042,1.125 0.198,0.177 10 false 12 4.313,1.104 4.573,1.281 0.26,0.177 10 false 10 5.865,2.688 6.063,2.865 0.198,0.177 10 false 5 5.865,3.083 6.063,3.26 0.198,0.177 10 false 6 5.865,4.708 6.063,4.885 0.198,0.177 10 false 8 5.865,5.104 6.063,5.281 0.198,0.177 10 false 9 4.375,2.552 4.573,2.729 0.198,0.177 10 false 8 4.375,3.281 4.573,3.458 0.198,0.177 10 false 1 4.375,4.563 4.573,4.74 0.198,0.177 10 false 7 4.302,5.271 4.646,5.469 0.344,0.198 10 false 28 2.448,4.813 3.708,5.052 1.26,0.24 10 false ECU-IG NO. 2 2.448,2.823 3.708,3.063 1.26,0.24 10 false ECU-IG NO. 2 0.51,2.677 2.01,2.917 1.5,0.24 10 false from IG1 NO. 1 Relay 0.51,4.667 2.01,4.906 1.5,0.24 10 false from IG1 NO. 1 Relay 2.448,0.667 3.708,0.906 1.26,0.24 10 false ECU-IG NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

B

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)
HINT:

When pre-crash safety system DTC U1002 is output, check that the local bus is functioning normally by performing the diagnostic procedure for U1002.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

3.CHECK CAN BUS LINE

B

GO TO PRE-CRASH SAFETY SYSTEM

3.CHECK CAN BUS LINE
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
A410116C14
1.531,0.167 1.948,0.385 0.417,0.219 2.146,1.125 2.396,0.99 true 2.167,1.427 2.406,1.51 true 0.167,0.094 0.479,0.292 0.313,0.198 10 false *a 2.448,0.875 2.948,1.104 0.5,0.229 10 false CANH 2.448,1.438 2.948,1.667 0.5,0.229 10 false CANL 1.615,0.198 2.115,0.427 0.5,0.229 10 false U15
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the U15 forward recognition camera connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U15-6 (CANH) - U15-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


HINT:

If the result is not as specified, a malfunction in a CAN communication line is suspected.



e.

Connect the U15 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAN BUS LINE)

4.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



Result:
Result Proceed to
DTC U0235 and U1104 are output A
Only DTC U1104 is output B
Only DTC U0235 is output C



A

5.CHECK POWER SOURCE CIRCUIT (DRIVING SUPPORT ECU ASSEMBLY)

B

7.CHECK POWER SOURCE CIRCUIT (DRIVING SUPPORT ECU ASSEMBLY)

C

10.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
5.CHECK POWER SOURCE CIRCUIT (DRIVING SUPPORT ECU ASSEMBLY)
a.
A418460C01
1.583,0.167 2,0.417 0.417,0.25 1.25,0.948 0.917,0.365 true 2.469,1.281 2.302,1.865 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.792,0.281 0.948,0.479 0.156,0.198 10 false B 1.979,1.792 2.438,1.99 0.458,0.198 10 false GND 1.646,0.208 2.26,0.406 0.615,0.198 10 false L205
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the L205 driving support ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L205-7 (B) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L205-28 (GND) - Body ground Always Below 1 Ω



f.

Reconnect the L205 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
A380144C89
1.479,0.177 1.854,0.406 0.375,0.229 0.885,0.792 1.406,1.052 true 1.969,1.198 2.573,1.5 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.552,0.208 1.865,0.406 0.313,0.198 10 false A91 0.458,0.708 1.073,0.906 0.615,0.198 10 false SGND 2.625,1.438 3.031,1.646 0.406,0.208 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A91 millimeter wave radar sensor assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-8 (IGB) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-1 (SGND) - Body ground Always Below 1 Ω



f.

Reconnect the A91 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

7.CHECK POWER SOURCE CIRCUIT (DRIVING SUPPORT ECU ASSEMBLY)
a.
A418460C01
1.583,0.167 2,0.417 0.417,0.25 1.25,0.948 0.917,0.365 true 2.469,1.281 2.302,1.865 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.792,0.281 0.948,0.479 0.156,0.198 10 false B 1.979,1.792 2.438,1.99 0.458,0.198 10 false GND 1.646,0.208 2.26,0.406 0.615,0.198 10 false L205
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the L205 driving support ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L205-7 (B) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L205-28 (GND) - Body ground Always Below 1 Ω



f.

Reconnect the L205 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

8.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
9.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.





Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA

10.CHECK POWER SOURCE CIRCUIT (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
A380144C89
1.479,0.177 1.854,0.406 0.375,0.229 0.885,0.792 1.406,1.052 true 1.969,1.198 2.573,1.5 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.552,0.208 1.865,0.406 0.313,0.198 10 false A91 0.458,0.708 1.073,0.906 0.615,0.198 10 false SGND 2.625,1.438 3.031,1.646 0.406,0.208 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A91 millimeter wave radar sensor assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-8 (IGB) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-1 (SGND) - Body ground Always Below 1 Ω



f.

Reconnect the A91 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

11.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
12.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.





Result:
Result Proceed to
DTC U0235 is not output A
DTC U0235 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA