If the forward recognition camera detects a malfunction in the internal circuit of the driving support ECU assembly, DTC C1A01 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A01 | Driving Support ECU | 2 seconds after the power switch is turned on (IG), a malfunction in the driving support ECU assembly internal circuit is detected for 5 seconds or more. | ·
Driving support ECU assembly ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
The lane departure alert system (w/ steering control) uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
When the lane departure alert system (w/ steering control) outputs DTC C1A01, the pre-crash safety system may also output DTC C1A01. If DTC C1A01 is output, perform diagnosis for the pre-crash safety system first.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A01 is not output | A |
| DTC C1A01 is output | B |
A
B
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 7 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A01 is not output | A |
| DTC C1A01 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL
Perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 7 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A01 is not output | A |
| DTC C1A01 is output | B |
A
B