The forward recognition camera uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.
When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the yaw rate sensor (airbag ECU assembly) etc., the millimeter wave radar sensor assembly performs self diagnosis to check if the sensor beam axis has deviated from the vehicle movement direction. When the millimeter wave radar sensor assembly beam axis has deviated, the forward recognition camera detects this, and stores DTC C1A11.
After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A11 | Front Radar Sensor Incorrect Axial Gap | 2 seconds after the power switch is turned on (IG), misalignment of the millimeter wave radar sensor assembly is detected for approximately 5 seconds. | ·
Millimeter wave radar sensor assembly ·
Forward recognition camera |
| C1A14 | Front Radar Sensor Beam Axis Not Adjusted | 2 seconds after the power switch is turned on (IG), incompletion of the millimeter wave radar sensor assembly beam axis alignment is detected for approximately 5 seconds. | ·
Millimeter wave radar sensor assembly ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
The lane departure alert system (w/ steering control) uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Current DTC C1A11 is output | A |
| Current DTC C1A14 is output | B |
| History DTC C1A11 is output | C |
A
B
C
Check the operating conditions of the vehicle.
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.
| Result | Proceed to |
|---|---|
| Vehicle is not overloaded or has not been towed. | A |
| Vehicle is overloaded or has been towed. | B |
A
B
Check the front and rear wheel alignment (toe).
for Front: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>INSPECTION
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels.
for Front: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the forward recognition camera.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 7 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A11 is not output | A |
| DTC C1A11 is output | B |
A
B
Check that the bracket of the millimeter wave radar sensor assembly is not deformed.
When the bracket is deformed, replace the millimeter wave radar sensor assembly.
The bracket is not deformed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Return the vehicle to normal operating conditions.
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 7 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A11 is not output | A |
| DTC C1A11 is output | B |
A
B
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
After performing the radar sensor beam axis adjustment, if the same DTC is output again after the DTC detection conditions are met, replace the forward recognition camera.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 7 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A14 is not output | A |
| DTC C1A14 is output | B |
A
B
Check the front and rear wheel alignment (toe).
for Front: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>INSPECTION
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Check that the bracket of the millimeter wave radar sensor assembly is not deformed.
When the bracket is deformed, replace the millimeter wave radar sensor assembly.
The bracket is not deformed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs related to misalignment of millimeter wave radar sensor assembly.
If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT