Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339647 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  C1AAD  Vehicle Information Initialization Incomplete  


DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the vehicle information received from the hybrid vehicle control ECU. If the forward recognition camera cannot store the vehicle information, DTC C1AAD is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAD Vehicle Information Initialization Incomplete 2 seconds after the power switch is turned on (IG), the vehicle information from the hybrid vehicle control ECU cannot be stored.
·

CAN communication system

·

Forward recognition camera

·

Hybrid vehicle control ECU



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)
HINT:

The forward recognition camera communicates with the hybrid vehicle control ECU via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



Result:
Result Proceed to
DTC U0293 is not output A
DTC U0293 is output B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Front Recognition Camera > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (2WD/4WD) Vehicle information 2WD, 4WD or Unknown 2WD: for 2WD
4WD: for AWD
Unknown: Vehicle information not confirmed
-
Vehicle Information (Conv/HV) Vehicle information Conv, HV or Unknown Conv: Conventional
HV: Hybrid vehicle
Unknown: Vehicle information not confirmed
-

HINT:
·

If "Unknown" is displayed, the hybrid vehicle control ECU cannot send vehicle information or the forward recognition camera cannot store the vehicle information. Check for DTCs, replace the hybrid vehicle control ECU if necessary and recheck for DTCs. If the DTC is output again, replace the forward recognition camera.

·

If "Unknown" is not displayed, the DTC is stored even though the vehicle information is stored in the forward recognition camera. Replace the forward recognition camera.




Result:
Result Proceed to
"Unknown" is displayed A
"Unknown" is not displayed B



A

3.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))

B

REPLACE FORWARD RECOGNITION CAMERA

3.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 seconds or more.





Result:
Result Proceed to
DTC C1AAD is not output A
DTC C1AAD is output B



A

B

4.REPLACE HYBRID VEHICLE CONTROL ECU
4.REPLACE HYBRID VEHICLE CONTROL ECU
a.

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))
5.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 seconds or more.





Result:
Result Proceed to
DTC C1AAD is not output A
DTC C1AAD is output B



A

END (HYBRID VEHICLE CONTROL ECU WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA