Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0339647 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  Lane Departure Alert System Switch Circuit  


DESCRIPTION

The driving support ECU assembly receives a lane departure alert switch signal from integration control and panel assembly and sends the signal to the forward recognition camera via CAN communication.

WIRING DIAGRAM

A415234E04
0.635,3.323 3.031,3.563 2.396,0.24 10 false : CAN Communication Line 2.646,1.198 3.104,1.396 0.458,0.198 10 false ECU 1.74,1.198 1.896,1.396 0.156,0.198 10 false E 1.542,1.198 1.698,1.396 0.156,0.198 10 false 2 3.021,1.198 3.177,1.396 0.156,0.198 10 false 5 1.396,1.938 3.271,2.469 1.875,0.531 10 false Lane Departure Alert Main Switch (Integration Control and Panel Assembly) 3.938,2.354 5.198,2.74 1.26,0.385 10 false Driving Support ECU Assembly 3.938,2.177 4.552,2.375 0.615,0.198 10 false L205 5.76,2.354 7.01,2.729 1.25,0.375 10 false Forward Recognition Camera 5.76,2.198 6.073,2.396 0.313,0.198 10 false U15 4.188,1.198 4.344,1.396 0.156,0.198 10 false 5 4.365,1.302 4.979,1.5 0.615,0.198 10 false PBSW 4.719,0.99 5.333,1.188 0.615,0.198 10 false CA1P 4.708,1.656 5.323,1.854 0.615,0.198 10 false CA1N 6.083,0.99 6.698,1.188 0.615,0.198 10 false CANH 6.094,1.646 6.708,1.844 0.615,0.198 10 false CANL 5.156,0.833 5.313,1.031 0.156,0.198 10 false 8 5.167,1.49 5.323,1.688 0.156,0.198 10 false 9 5.917,0.844 6.073,1.042 0.156,0.198 10 false 6 5.823,1.49 6.115,1.719 0.292,0.229 10 false 12 1.396,1.781 2.01,1.979 0.615,0.198 10 false L177

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.


Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (HEALTH CHECK)

B

2.CHECK FOR DTCs (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check DTCs.


f.

Turn the power switch off.


Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



A

3.INSPECT LANE DEPARTURE ALERT MAIN SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

B

GO TO DTC CHART

3.INSPECT LANE DEPARTURE ALERT MAIN SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.

Remove the lane departure alert main switch (integration control and panel assembly).

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SWITCH>REMOVAL


b.

Inspect the lane departure alert main switch (integration control and panel assembly).

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE ALERT MAIN SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPLACE LANE DEPARTURE ALERT MAIN SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE ALERT MAIN SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY) - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the L177 lane departure alert main switch (integration control and panel assembly) connector.


b.

Disconnect the L205 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L177-5 (ECU) - L205-5 (PBSW) Always Below 1 Ω
L177-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L177-5 (ECU) or L205-5 (PBSW) - Body ground Always 10 kΩ or higher



d.

Connect the L205 driving support ECU assembly connector.


e.

Connect the L177 lane departure alert main switch (integration control and panel assembly) connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR