Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A47  Steering Angle Sensor  


DESCRIPTION

The driving support ECU assembly receives steering angle information from the steering sensor (spiral cable with sensor sub-assembly). If the driving support ECU assembly detects a steering sensor (spiral cable with sensor sub-assembly) malfunction, DTC C1A47 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A47 Steering Angle Sensor While the vehicle is being driven at a speed of 50 km/h (32 mph) or more, the driving support ECU assembly receives a steering sensor (spiral cable with sensor sub-assembly) malfunction signal continuously for 1 second or more.
·

Electronically controlled brake system

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

Pre-crash safety system DTC C1A47 may be stored due to a malfunction in the electronically controlled brake system. Therefore, it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.



Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

B

2.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Drive the vehicle at a speed of 50 km/h (32 mph) or more for 1 second or more.





Result:
Result Proceed to
DTC C1A47 is not output A
DTC C1A47 is output B



A

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
4.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Drive the vehicle at a speed of 50 km/h (32 mph) or more for 1 second or more.





Result:
Result Proceed to
DTC C1A47 is not output A
DTC C1A47 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)