Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

The driving support ECU assembly operates the pre-crash warning by sending a buzzer request signal to the skid control buzzer assembly.

If the driving support ECU assembly detects a malfunction in the skid control buzzer assembly circuit, it will store DTC C1A4A.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit When the power switch is on (IG) and the pre-crash warning is operating, either of the following conditions is met:
·

A buzzer request signal is sent to the skid control buzzer assembly but the buzzer does not sound for 1 second or more.

·

A buzzer request signal is not sent to the skid control buzzer assembly but the buzzer sounds for 1 second or more.


·

Skid control buzzer assembly

·

Driving support ECU assembly

·

Wire harness or connector



WIRING DIAGRAM

B456420E31
0.146,0.688 1.688,0.927 1.542,0.24 10 false from IG1 NO. 1 Relay 2.115,0.844 3.208,1.063 1.094,0.219 10 false ECU-IG NO. 2 3.385,1.208 5.542,1.438 2.156,0.229 10 false Skid Control Buzzer Assembly 3.396,1.042 3.75,1.25 0.354,0.208 10 false L46 3.396,0.583 3.563,0.76 0.167,0.177 10 false 2 4.49,0.573 4.656,0.75 0.167,0.177 10 false 1 5.521,0.698 5.875,0.906 0.354,0.208 10 false BZ 5.354,0.573 5.521,0.75 0.167,0.177 10 false 3 5.063,1.958 5.417,2.167 0.354,0.208 10 false L205 5.052,2.115 7.021,2.333 1.969,0.219 10 false Driving Support ECU Assembly 4.25,0.698 4.604,0.906 0.354,0.208 10 false BZ 3.573,0.698 3.927,0.906 0.354,0.208 10 false IG1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


g.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with power switch on (IG), vehicle stopped


h.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

B

2.CHECK TERMINAL VOLTAGE
2.CHECK TERMINAL VOLTAGE
a.
B443157C42
1.5,0.177 1.906,0.438 0.406,0.26 1.979,1.365 2.438,1.135 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.594,0.229 2.052,0.427 0.458,0.198 10 false L46 2.479,1.042 2.938,1.24 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer Assembly)


Disconnect the L46 skid control buzzer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L46-2 (IG1) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



c.

Connect the L46 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - AUXILIARY BATTERY)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the L46 skid control buzzer assembly connector.


b.

Disconnect the L205 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L46-1 (BZ) - L205-3 (BZ) Always Below 1 Ω
L46-1 (BZ) or L205-3 (BZ) - Body ground Always 10 kΩ or higher



d.

Connect the L205 driving support ECU assembly connector.


e.

Connect the L46 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


g.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with power switch on (IG), vehicle stopped


h.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
a.

Turn the power switch on (IG).


b.

Check if the skid control buzzer assembly is sounding.


Result:
Result Proceed to
The skid control buzzer assembly does not sound when the power switch is on (IG) A
The skid control buzzer assembly sounds continuously when the power switch is on (IG) B



A

7.INSPECT SKID CONTROL BUZZER ASSEMBLY (UNIT INSPECTION)

B

8.REPLACE SKID CONTROL BUZZER ASSEMBLY
7.INSPECT SKID CONTROL BUZZER ASSEMBLY (UNIT INSPECTION)
a.

b.

Result:
Result Proceed to
skid control buzzer assembly is abnormal A
skid control buzzer assembly is normal B



A

8.REPLACE SKID CONTROL BUZZER ASSEMBLY

B

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
8.REPLACE SKID CONTROL BUZZER ASSEMBLY
a.

Replace the skid control buzzer assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


g.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with power switch on (IG), vehicle stopped


h.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY