When the pre-crash safety system is operating, the driving support ECU assembly sends brake control signals to the skid control ECU (brake booster with master cylinder assembly).
If the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly) via CAN communication, DTC C1A50 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A50 | Brake System Malfunction | While the power switch is on (IG), the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly) for 0.3 seconds or more. | ·
Electronically controlled brake system ·
Skid control ECU (Brake booster with master cylinder assembly) ·
Driving support ECU assembly |
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Pre-crash safety system DTC C1A50 may be stored due to a malfunction in the electronically controlled brake system. Therefore, it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Electronically controlled brake system DTCs are not output | A |
| Electronically controlled brake system DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 0.3 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A50 is not output | A |
| DTC C1A50 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the driving support ECU assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.
Clear the DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the power switch on (IG) and wait 0.3 seconds or more.
Check for DTCs.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A50 is not output | A |
| DTC C1A50 is output | B |
A
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>COMPONENTS
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>COMPONENTS