Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL PUMP › from 2017.12
RM2070E _51 Engine / Hybrid System _061908 2ZR-FXE FUEL _0301607 FUEL PUMP A

2ZR-FXE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A251210E01
2.836,0.188 3.009,0.382 0.173,0.194 10 *1 2.606,0.442 2.752,0.295 2.752,0.295 2.833,0.295 false

Install a new fuel suction tube set gasket onto the fuel tank assembly.

Text in Illustration
*1 Fuel Suction Tube Set Gasket


b.
A251211E02
1.094,4.031 1.094,4.344 false 2.396,4.031 2.396,4.229 2.396,4.229 1.094,4.229 false 1.177,2.052 2.354,2.906 2.354,2.906 2.354,1.552 false 2.281,2.938 2.448,3.115 0.167,0.177 10 false *a 1.01,4.333 1.177,4.51 0.167,0.177 10 false *b

Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

Text in Illustration
*a Notch
*b Protrusion

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.

Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches of the fuel tank assembly.


d.
A413980C02
0.885,0.802 1.042,0.802 1.042,0.802 1.24,1.073 true 0.708,0.719 0.917,0.896 0.208,0.177 10 true *a
*a Paint Mark


Place a paint mark on the fuel suction tube with pump and gauge assembly as shown in the illustration.

HINT:

Perform this step only when replacing the fuel suction tube with pump and gauge assembly.



Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.
A413981C02
2.094,4.125 2.802,3.938 2.802,3.938 2.979,3.938 true 2.365,4.49 2.833,4.49 true 2.375,4.448 2.865,4.313 2.865,4.313 2.104,4.125 true 2.885,4.417 3.198,4.573 0.313,0.156 10 false *a 3.021,3.875 3.333,4.031 0.313,0.156 10 false *b 2.927,4.25 3.24,4.406 0.313,0.156 10 false *c
*a Copy of Start of Threads Mark
*b Start of Threads of the Fuel Pump Gauge Retainer
*c Align
V100135

Press down
V100136

Front


Align the start of the threads of a new fuel pump gauge retainer with the start of threads mark that was copied onto the vehicle body and while pushing down the fuel suction tube with pump and gauge assembly, attach the fuel pump gauge retainer.


b.

Install SST to the fuel pump gauge retainer.

i.
A381189C02
2.115,0.208 2.26,0.208 2.26,0.208 2.385,0.375 false 0.604,1.24 0.906,1.24 false 1.208,1.385 1.51,1.385 false 1.177,2.167 1.406,2.167 false 1.115,2.406 1.229,2.406 1.229,2.406 1.563,2.573 true 1.854,2.573 1.99,2.344 1.99,2.344 2.083,2.344 false 1.104,3.104 1.292,3.104 1.292,3.104 1.563,2.677 true 0.563,4.458 0.75,4.458 0.75,4.458 1.385,4.042 true 2.604,1.708 2.604,1.469 false 1.563,1.313 1.875,1.469 0.313,0.156 10 false *1 0.438,1.156 0.75,1.313 0.313,0.156 10 false *a 0.917,3.031 1.229,3.188 0.313,0.156 10 false *b 0.938,2.333 1.25,2.49 0.313,0.156 10 false *c 0.375,4.396 0.688,4.552 0.313,0.156 10 false *d 1.948,0.146 2.26,0.302 0.313,0.156 10 false *1 1.01,2.083 1.323,2.24 0.313,0.156 10 false *a 2.146,2.281 2.458,2.438 0.313,0.156 10 false *1 2.531,1.729 2.844,1.885 0.313,0.156 10 false *a
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Protrusion
*c Notch
*d Do not install SST (Claw Set)


Set 4 SST (claw set) to the fuel pump gauge retainer.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the notch of SST (claw set) with the protrusion of the fuel pump gauge retainer.

·

Do not install SST (claw set) to the start of threads location of the fuel pump gauge retainer.




ii.
A381190C02
1.031,0.396 1.302,0.396 false 0.927,2.052 1.063,2.052 1.063,2.052 1.229,1.823 false 2.135,1.302 2.24,1.052 2.24,1.052 2.344,1.052 false 2.406,0.979 2.719,1.135 0.313,0.156 10 false *1 0.844,0.313 1.156,0.469 0.313,0.156 10 false *a 0.75,1.979 1.063,2.135 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Push
V100136

SST (Bolt)


Push SST (claw set) against the fuel pump gauge retainer and tighten SST (bolt).


iii.
A413975C02
0.583,0.833 0.854,0.833 false 0.563,1.177 1.01,1.177 true 0.979,1.75 1.688,1.75 true 2.438,1.115 2.917,1.115 true 0.406,0.771 0.719,0.927 0.313,0.156 10 false *a 0.396,1.125 0.708,1.281 0.313,0.156 10 false *b 0.802,1.698 0.979,1.844 0.177,0.146 10 true *b 2.969,1.052 3.281,1.208 0.313,0.156 10 false *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SST (bolt).

SST
09808-14031  (09808-01030, 09808-01090)


iv.
A413982C02
0.875,0.656 1.01,0.656 1.01,0.656 1.698,1.188 true 0.583,1.271 0.927,1.271 true 0.677,0.583 0.865,0.729 0.188,0.146 10 true *a 0.406,1.198 0.719,1.354 0.313,0.156 10 false *b
*a Center Point of Fuel Pump Gauge Retainer
*b SST (Plate)
V100135

Front


Adjust the position of SST (claw set) so that the hole in SST (plate) for installing SST (handle) is in the center of the fuel pump gauge retainer.


v.
A413977C02
1.146,0.104 1.365,0.104 1.365,0.104 1.771,0.188 true 1.115,0.302 1.458,0.302 true 1.188,0.552 1.344,0.552 1.344,0.552 1.646,0.708 true 1.75,1.948 1.896,1.948 1.896,1.948 2.135,1.563 true 1.583,1.896 1.896,2.052 0.313,0.156 10 false *1 0.948,0.24 1.26,0.396 0.313,0.156 10 false *a 1.021,0.5 1.333,0.656 0.313,0.156 10 false *b 0.969,0.031 1.281,0.188 0.313,0.156 10 false *c
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
V100135

Press


Press SST (claw set) against the rib of the fuel pump gauge retainer and tighten SST (bolt).



c.
A413983C02
0.896,1.125 0.885,1.427 0.885,1.427 1.229,1.198 true 2.385,2.865 2.51,2.396 2.51,2.396 2.615,2.396 true 0.875,2.635 0.979,2.635 0.979,2.635 1.042,2.719 false 0.813,3.271 1.021,3.271 false 0.708,2.552 1.021,2.708 0.313,0.156 10 false *1 0.646,3.177 0.958,3.333 0.313,0.156 10 false *2 2.667,2.323 2.979,2.479 0.313,0.156 10 false *a 1.542,1.802 1.708,1.948 0.167,0.146 10 true *b 1.75,0.344 1.958,0.479 0.208,0.135 10 true *c 0.552,3.563 0.865,3.719 0.313,0.156 10 false *d 0.76,1.438 0.948,1.583 0.188,0.146 10 true *e
*1 Fuel Pump Gauge Retainer
*2 Fuel Tank Assembly
*a SST (Plate)
*b Tighten approximately 90°
*c Fuel pump gauge retainer rises up
*d Cross Section
*e Paint Mark
V100135

Press quickly and firmly
V100136

Front


While pressing down on the fuel suction tube with pump and gauge assembly, have another person firmly press the fuel pump gauge retainer against the threads of the fuel tank assembly, and tighten the fuel pump gauge retainer by approximately 90°.

NOTICE:
·

To prevent damage to parts, do not turn SST too vigorously.

·

Do not turn the fuel pump gauge retainer if the paint marks become misaligned.




d.

Quickly and firmly press down on the part of the fuel pump gauge retainer closest to the rear of the vehicle to keep it from rising up.

HINT:
·

If the fuel pump gauge retainer cannot be properly pressed down due to the position of SST, set SST in a different position.

·

When fully pressing down the fuel pump gauge retainer, there will be a sound or tactile sensation of parts contacting each other, and at this point the fuel suction tube with pump and gauge assembly will stop rising up.




e.
A413984C02
1.396,2.188 1.396,1.854 1.396,1.854 1.604,1.667 true 2.385,4.479 2.792,4.479 true 1.292,2.198 1.604,2.354 0.313,0.156 10 false *a 0.99,1.052 1.302,1.208 0.313,0.156 10 false *b 1.281,0.51 1.594,0.667 0.313,0.156 10 false *c 2.844,4.417 3.156,4.573 0.313,0.156 10 false *d 2.344,1.063 2.656,1.219 0.313,0.156 10 false *b 2.031,0.542 2.344,0.698 0.313,0.156 10 false *c
*a SST (Plate)
*b One Person in Charge of Tightening
*c One Person in Charge of Pressing Down
*d Copy of Start of Threads Mark
V100135

Front


While pressing down on the fuel suction tube with pump and gauge assembly, have another person slowly tighten the fuel pump gauge retainer until it reaches the start of threads mark.


f.
A413985C02
0.677,1.25 1.031,1.25 true 1.823,0.271 1.938,0.271 1.938,0.271 1.969,0.677 true 1.927,1.99 1.927,2.375 true 1.219,2.896 1.354,2.896 1.354,2.896 1.469,3.25 false 1.25,3.99 1.542,3.99 false 2.25,3.063 2.542,3.063 false 1.042,2.833 1.354,2.99 0.313,0.156 10 false *1 1.063,3.927 1.375,4.083 0.313,0.156 10 false *2 0.49,1.167 0.802,1.323 0.313,0.156 10 false *a 2.594,2.99 2.906,3.146 0.313,0.156 10 false *b 1.635,0.198 1.813,0.354 0.177,0.156 10 true *a 1.854,2.375 2.031,2.531 0.177,0.156 10 true *a 2.063,1.083 2.198,1.229 0.135,0.146 10 true A 2.396,0.521 2.531,0.667 0.135,0.146 10 true A 1.385,4.333 1.833,4.51 0.448,0.177 10 false A - A
*1 Fuel Pump Gauge Retainer
*2 Fuel Tank Assembly
*a Measurement Position
*b Vernier Caliper
V100136

Front


Check the tightening status of the fuel pump gauge retainer.

i.

Using a vernier caliper, measure the distance from the fuel tank assembly to the upper surface of the fuel pump gauge retainer at 3 positions as shown in the illustration.

Standard:

Difference between the 3 measured values is 3 mm (0.118 in.) or less.


NOTICE:

If the difference between measurements is approximately 6 mm (0.236 in.), the threads are cross-threaded by 1 row (6 mm (0.236 in.)), so remove and reinstall the fuel pump gauge retainer.




g.
A413986C02
0.771,0.323 0.917,0.323 0.917,0.323 1.052,0.76 true 1.375,1.958 1.375,1.74 1.375,1.74 1.583,1.469 true 0.604,0.24 0.917,0.396 0.313,0.156 10 false *a 1.281,1.99 1.594,2.146 0.313,0.156 10 false *b 0.531,0.729 0.844,0.885 0.313,0.156 10 false *c 1.354,0.51 1.667,0.667 0.313,0.156 10 false *d 1.479,4.042 1.677,4.198 0.198,0.156 10 true *e 2.75,0.792 3.063,0.948 0.313,0.156 10 false *c 2.021,0.49 2.333,0.646 0.313,0.156 10 false *d
*a SST (Handle)
*b SST (Plate)
*c One Person in Charge of Tightening
*d One Person in Charge of Pressing Down
*e Approximately 90°
V100135

Front


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


h.

While pressing down on the fuel suction tube with pump and gauge assembly, have another person use SST (handle) to slowly tighten the fuel pump gauge retainer approximately 90°.


i.
A413987C02
0.76,0.333 0.906,0.333 0.906,0.333 1.042,0.76 true 1.385,1.969 1.385,1.625 1.385,1.625 1.573,1.51 true 0.854,2.958 0.854,2.552 0.854,2.552 1.167,2.552 true 0.604,3.26 0.74,3.26 0.74,3.26 1.354,3.104 true 0.594,2.927 0.99,2.927 true 0.583,0.26 0.896,0.417 0.313,0.156 10 false *a 1.313,2 1.625,2.156 0.313,0.156 10 false *b 0.427,3.188 0.74,3.344 0.313,0.156 10 false *d 0.406,2.854 0.719,3.01 0.313,0.156 10 false *c
*a SST (Handle)
*b SST (Plate)
*c Copy of Fully Tightened Mark
*d Start of Threads of the Fuel Pump Gauge Retainer
V100135

Tighten
V100136

Front


Slowly tighten the fuel pump gauge retainer until it reaches between the fully tightened marks that were copied onto the vehicle body.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A413988C02
3.76,1.375 5.115,2.625 1.354,1.25 5.281,1.365 6.635,2.615 1.354,1.25 2.396,1.76 2.719,1.167 2.719,1.167 2.948,1.167 true 2.385,2.438 2.385,2.219 true 4.438,0.521 4.688,0.521 false 4.469,0.844 4.573,0.844 4.573,0.844 4.729,0.677 false 5.135,0.677 5.385,0.677 5.385,0.677 5.385,0.792 false 5.167,0.792 5.5,0.792 false 4.135,1.833 4.427,1.833 false 4.271,2.302 4.406,2.302 4.406,2.302 4.625,1.969 true 5.99,1.615 6.125,1.615 6.125,1.615 6.25,1.896 true 5.833,1.917 6.021,1.917 false 4.281,0.781 4.594,0.938 0.313,0.156 10 false *1 4.25,0.469 4.563,0.625 0.313,0.156 10 false *2 3.021,1.104 3.333,1.26 0.313,0.156 10 false *3 5.552,0.729 5.865,0.885 0.313,0.156 10 false *a 3.823,1.427 4.135,1.583 0.313,0.156 10 false *b 5.344,1.406 5.656,1.563 0.313,0.156 10 false *c 4.094,2.25 4.406,2.406 0.313,0.156 10 false *d 3.958,1.781 4.271,1.938 0.313,0.156 10 false *2 5.635,1.854 5.948,2.01 0.313,0.156 10 false *2 2.292,2.479 2.604,2.635 0.313,0.156 10 false *2 5.823,1.552 6.135,1.708 0.313,0.156 10 false *d
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a O-ring *b Correct
*c Incorrect *d Collar
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint as shown in the illustration.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 4. CHECK AIRTIGHTNESS

a.
A413989C02
0.479,1.479 1.292,1.479 true 0.302,1.385 0.615,1.542 0.313,0.156 10 false *a
*a Soapy Water Application Area


Apply soapy water to the contact areas between the fuel suction tube with pump and gauge assembly and fuel pump gauge retainer.

NOTICE:

Cover the connector of the fuel suction tube with pump and gauge assembly with protective tape.



b.
A413990C02
0.573,0.51 0.708,0.51 0.708,0.51 0.885,0.885 false 1.281,1.302 1.469,1.302 1.469,1.302 1.896,1.854 true 0.396,0.448 0.708,0.604 0.313,0.156 10 false *a 1.115,1.24 1.427,1.396 0.313,0.156 10 false *b
*a Vacuum Pump
*b Port (A)


Install a vacuum pump to the port (A) of the fuel suction tube with pump and gauge assembly as shown in the illustration.


c.
A413991C02
0.542,0.49 0.667,0.49 0.667,0.49 0.885,0.885 false 1.323,1.281 1.438,1.281 1.438,1.281 1.896,1.823 true 2.385,2.344 2.781,1.677 2.781,1.677 2.906,1.677 true 1.135,1.208 1.448,1.365 0.313,0.156 10 false *a 2.979,1.615 3.292,1.771 0.313,0.156 10 false *b 0.365,0.427 0.677,0.583 0.313,0.156 10 false *c
*a Port (A)
*b Port (B)
*c Vacuum Pump


Close the port (A) and using the vacuum pump, apply 5 kPa (0.1 kgf/cm2, 0.7 psi) of compressed air to the port (B) as shown in the illustration.

NOTICE:

Do not apply more compressed air than necessary.



d.

Check that the contact areas between the fuel suction tube with pump and gauge assembly and fuel pump gauge retainer are airtight.

NOTICE:
·

If air bubbles appear, remove and reinstall the fuel pump gauge retainer.

·

After a fuel pump gauge retainer and fuel suction tube set gasket have been used once, replace them with new parts.

·

When removing and reinstalling the fuel pump gauge retainer, make sure to clean away the soapy water to prevent the fuel suction tube set gasket from slipping out of position and being assembled incorrectly.



HINT:
A413992C02
0.438,1.333 1.667,1.333 true 0.26,1.25 0.573,1.406 0.313,0.156 10 false *a
*a Air Bubbles


If the assembled components are not airtight due to improper installation of the fuel pump gauge retainer, etc., air bubbles will appear as shown in the illustration.



Hide 77026A 5.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.


Hide 77754B 6.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.

Connect the charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly.


Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 58325E 9.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the fuel pump connector.


d.

Install the rear floor service hole cover with new butyl tape.


e.

Install the rear floor carpet with the 2 clips.


Hide 15.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 16.INSTALL REAR NO. 1 SEAT ASSEMBLY (for Center)

Hide 17.INSTALL REAR NO. 1 SEAT ASSEMBLY (for Side)