1.SET ROOF HEADLINING ASSEMBLY
Put the roof headlining assembly into the vehicle through the front of the vehicle.
Do not damage the roof headlining assembly or vehicle interior.
Temporarily install the roof headlining assembly so that the windshield glass can be installed.
56111
2.INSTALL WINDSHIELD GLASS
3.INSTALL ROOF HEADLINING ASSEMBLY (except Glass Roof)
Install the roof headlining assembly with the 5 clips.
for Rear Pillar RH Side:
w/o Radio Receiver:
Connect the connector.
Engage the claw.
w/ Radio Receiver:
Connect each connector.
Engage the guide and claw.
for Front Pillar RH Side:
Remove the protective cover.
Connect each connector.
Engage the 3 clamps.
Install the protective cover.
for Front Pillar LH Side:
Remove the protective cover.
Connect each connector.
Engage the 3 clamps.
Install the protective cover.
for Windshield Glass Side:
w/ EC mirror or Pre-crash Safety System:
Connect each connector.
4.INSTALL ROOF HEADLINING ASSEMBLY (for Glass Roof)
Engage the 15 fasteners.
Install the roof headlining assembly with the 3 clips.
for Rear Pillar RH Side:
w/o Radio Receiver:
Connect the connector.
Engage the claw.
w/ Radio Receiver:
Connect each connector.
Engage the guide and claw.
for Front Pillar RH Side:
Remove the protective cover.
Connect each connector.
Engage the 3 clamps.
Install the protective cover.
for Front Pillar LH Side:
Remove the protective cover.
Connect the 2 connectors.
Engage the 3 clamps.
Install the protective cover.
for Windshield Glass Side:
Connect each connector.
74348
5.INSTALL VISOR HOLDER
Engage the 2 claws.
Install the visor holder as shown in the illustration.
Use the same procedure for the other visor holder.
74320
6.INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the 2 screws.
74310
7.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74610S
8.INSTALL FRONT ASSIST GRIP ASSEMBLY
Assemble the front assist grip assembly as shown in the illustration.
Install the front assist grip assembly.
Use the same procedure for the other front assist grip assembly.
74620B
9.INSTALL REAR ASSIST GRIP ASSEMBLY
Use the same procedure as for the front assist grip assembly.
73139A
10.INSTALL SEAT BELT ANCHOR COVER
Engage the 2 guides and 2 claws, 2 clips to install the seat belt anchor cover.
81240
11.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
81260A
12.INSTALL MAP LIGHT ASSEMBLY (except Glass Roof)
81260A
13.INSTALL MAP LIGHT ASSEMBLY (for Glass Roof)
86466D
14.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)
86466E
15.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)
89943
16.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
87818
17.INSTALL INNER REAR VIEW MIRROR COVER (w/ Cover)
62452C
18.INSTALL REAR ROOF SIDE RAIL GARNISH LH
Engage the guide and 4 claws to install the rear roof side rail garnish LH.
62480A
19.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH
Pass the floor anchor of the rear seat outer seat belt assembly LH through the roof side inner garnish assembly LH.
Insert the roof side inner garnish assembly LH in the direction indicated by the arrow (1) shown in the illustration and engage the 3 clips (B).
Insert the roof side inner garnish assembly LH in the direction indicated by the arrow (2) shown in the illustration and engage the 7 clips (A) to install the roof side inner garnish assembly LH and rear roof side rail garnish LH as a unit.
Engage the 2 guides.
Engage the 2 claws to install the belt guide LH.
73570
20.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (for Upper Side)
64740C
21.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Engage the 5 guides, 5 clips and 7 claws.
Make sure that the 4 guides (A) of the deck trim side panel assembly LH are inserted securely to prevent any excessive gaps.
Install the deck trim side panel assembly LH with the 2 bolts.
81250
22.INSTALL NO. 2 ROOM LIGHT ASSEMBLY
73570
23.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (for Lower Side)
73370C
24.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
55548C
25.INSTALL NO. 2 CUP HOLDER
Engage the 12 claws to install the No. 2 cup holder.
64713F
26.INSTALL FRONT DECK SIDE TRIM COVER LH
Engage the 2 guides.
Engage the 2 claws to install the front deck side trim cover LH.
58460D
27.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)
Engage the 2 guides.
Install the 2 luggage hold belt striker assemblies with the 2 bolts.
64721G
28.INSTALL NO. 1 DECK TRIM COVER (for LH Side)
Engage the 2 guides and 3 claws to install the No. 1 deck trim cover.
62451C
29.INSTALL REAR ROOF SIDE RAIL GARNISH RH
Use the same procedure as for the LH side.
62471A
30.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
73560
31.INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (for Upper Side)
Use the same procedure as for the LH side.
64730B
32.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
73560
33.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (for Lower Side)
Use the same procedure as for the LH side.
73360C
34.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
55548C
35.INSTALL NO. 1 CUP HOLDER
Connect the connector.
Engage the 12 claws to install the No. 1 cup holder.
64712F
36.INSTALL FRONT DECK SIDE TRIM COVER RH
Use the same procedure as for the LH side.
58460D
37.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
64721G
38.INSTALL NO. 1 DECK TRIM COVER (for RH Side)
Use the same procedure as for the LH side.
62412
39.INSTALL CENTER PILLAR GARNISH LH
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.
Engage the 2 clips to install the center pillar garnish LH.
Install the center pillar garnish LH with the bolt.
62414A
40.INSTALL CENTER PILLAR LOWER GARNISH LH
Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.
73220
41.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
73233
42.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
62332A
43.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *a | Alignment Mark (Red) |
After installation, check that the corners fit correctly.
67918A
44.INSTALL REAR DOOR SCUFF PLATE LH
Move the rear seat assembly LH to the foremost position.
Engage the 9 claws and 3 clips to install the rear door scuff plate LH.
62212
45.INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Engage the front pillar garnish clip to the front pillar garnish LH.
Make sure that the front pillar garnish clip is engaged correctly.
| *1 | Front Pillar Garnish Clip | *2 | Front Pillar Garnish LH |
| *a | Correct | *b | Incorrect |
Engage the guide (B) in the direction indicated by the arrow (1) shown in the illustration.
Engage the 2 guides (A) in the direction indicated by the arrow (2) shown in the illustration.
Engage the clip and front pillar garnish clip to install the front pillar garnish LH as shown in the illustration.
Make sure that the curtain shield airbag assembly LH is not pinched.
62312B
46.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *a | Alignment Mark (Yellow) |
After installation, check that the corners fit correctly.
62112A
47.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the clip.
67914
48.INSTALL FRONT DOOR SCUFF PLATE LH
Engage the 10 claws to install the front door scuff plate LH.
62411
49.INSTALL CENTER PILLAR GARNISH RH
Use the same procedure as for the LH side.
62413A
50.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
73210
51.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
73233
52.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
Use the same procedure as for the LH side.
62331A
53.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| *a | Alignment Mark (Blue) |
After installation, check that the corners fit correctly.
67917A
54.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62211
55.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62311B
56.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Align the alignment mark (White) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *a | Alignment Mark (White) |
After installation, check that the corners fit correctly.
62111C
57.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
67913
58.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
59.INSTALL REAR NO. 2 SEAT ASSEMBLY
72128C
60.INSTALL SEAT TRACK BRACKET COVER LH
72159H
61.INSTALL REAR SEAT TRACK BRACKET COVER
72127D
62.INSTALL SEAT TRACK BRACKET COVER RH
67935A
63.INSTALL BACK DOOR SCUFF PLATE
Engage the 2 guides and 2 claws, 4 clips to install the back door scuff plate.
64910J
64.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Install the tonneau cover assembly.
64995
65.INSTALL DECK FLOOR BOX RH
Engage the 3 claws to install the deck floor box RH.
64993
66.INSTALL REAR DECK FLOOR BOX
Install the rear deck floor box.
58411A
67.INSTALL NO. 1 DECK BOARD
Install the No. 1 deck board.
58412A
68.INSTALL NO. 2 DECK BOARD
Install the No. 2 deck board.
58410B
69.INSTALL DECK BOARD ASSEMBLY
Install the deck board assembly.