The stroke sensor inputs the pedal stroke into the skid control ECU.
DTC C1346 will be cleared when the brake pedal stroke sensor sends a stroke sensor signal or when Test Mode ends. DTC C1346 is output only in Test Mode.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1247 | 211 | Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.2 seconds or more. | ·
Open or short in brake pedal stroke sensor power supply circuit ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 212 | Sensor output voltage 1 (SKS1) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more. | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor |
| ↑ | 213 | Sensor output voltage 2 (SKS2) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCSK) for 0.2 seconds or more. | ↑ |
| ↑ | 214 | Either of the following is detected:
1.
Fluctuation of sensor output 1 (SKS1) is out of specification. 2.
The difference between the present value and last value of sensor output voltage 1 (SKS1) is 8.5% or more (0.43 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more. |
↑ |
| ↑ | 215 | Either of the following is detected:
1.
Fluctuation of sensor output 2 (SKS2) is out of specification. 2.
The difference between the present value and last value of the sensor output voltage 2 (SKS2) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) for 0.2 seconds or more. |
↑ |
| ↑ | 218 | An excessive difference between the change in sensor output 1 (SKS1) and sensor output 2 (SKS2) is detected for 0.2 seconds or more. | ↑ |
| ↑ | 219 | Sensor data is invalid for 0.2 seconds or more.
(Skid control ECU internal monitor circuit malfunction.) |
↑ |
| ↑ | 223 | Sensor data is invalid for 0.2 seconds or more.
(Open, short, or noise.) |
↑ |
| C1392 | - | Zero point calibration of stroke sensor is unfinished. | ·
Brake pedal stroke sensor zero point calibration incomplete (Initialization and calibration of linear solenoid valve incomplete) ·
Brake booster with master cylinder (Skid control ECU) |
| C1346 | - | Detected only during Test Mode. | ·
Brake pedal stroke sensor ·
Brake pedal stroke sensor circuit |
When replacing the brake booster with master cylinder (skid control ECU) or brake pedal stroke sensor, perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Check the condition of each related circuit connector before troubleshooting (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Check that the brake pedal and the brake pedal stroke sensor are properly installed and that the pedal can be depressed normally.
Check and adjust the brake pedal height (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT for LHD, or Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT for RHD).
Adjust the brake pedal stroke sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>INSTALLATION for LHD, or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>INSTALLATION for RHD).
NEXT
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector and the brake pedal stroke sensor connector.
Check both the connector case and the terminal for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-39 (VCSK) - A30-3 (VCSK) | Always | Below 1 Ω |
| A58-39 (VCSK) - Body ground | Always | 10 kΩ or higher |
| A58-41 (SKG) - A30-1 (SKG) | Always | Below 1 Ω |
| A58-41 (SKG) - Body ground | Always | 10 kΩ or higher |
| A58-42 (SKS) - A30-4 (SKS1) | Always | Below 1 Ω |
| A58-42 (SKS) - Body ground | Always | 10 kΩ or higher |
| A58-40 (SKS2) - A30-2 (SKS2) | Always | Below 1 Ω |
| A58-40 (SKS2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-39 (VCSK) - A30-3 (VCSK) | Always | Below 1 Ω |
| A58-39 (VCSK) - Body ground | Always | 10 kΩ or higher |
| A58-41 (SKG) - A30-1 (SKG) | Always | Below 1 Ω |
| A58-41 (SKG) - Body ground | Always | 10 kΩ or higher |
| A58-42 (SKS) - A30-2 (SKS1) | Always | Below 1 Ω |
| A58-42 (SKS) - Body ground | Always | 10 kΩ or higher |
| A58-40 (SKS2) - A30-4 (SKS2) | Always | Below 1 Ω |
| A58-40 (SKS2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the skid control ECU connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-3 (VCSK) - A30-1 (SKG) | Power switch on (IG) | 4.84 to 5.16 V |
| *a | Front view of wire harness connector
(to Brake Pedal Stroke Sensor) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D