Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Open in Bus 5 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

No. 4 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C354532E07
0.969,1.333 1.74,1.531 0.771,0.198 10 false 120 Ω 0.958,3.792 1.729,3.99 0.771,0.198 10 false 120 Ω 0.302,4.427 1.073,4.625 0.771,0.198 10 false L192 0.635,4.427 2.583,5.146 1.948,0.719 10 false Central Gateway ECU (Network Gateway ECU) 5.01,4.396 6.906,4.865 1.896,0.469 10 false No. 4 CAN Junction Connector 1.594,1 2.073,1.208 0.479,0.208 10 false CA5H 1.625,1.469 2.094,1.656 0.469,0.188 10 false CA5L 2.052,1 2.531,1.208 0.479,0.208 10 false 15 2.042,1.458 2.521,1.667 0.479,0.208 10 false 16 1.583,3.438 2.063,3.646 0.479,0.208 10 false CAXH 1.594,3.917 2.073,4.125 0.479,0.208 10 false CAXL 2.063,3.438 2.542,3.646 0.479,0.208 10 false 9 2.063,3.906 2.542,4.115 0.479,0.208 10 false 24 5.167,1.104 5.646,1.313 0.479,0.208 10 false L198 5.167,1.573 5.646,1.781 0.479,0.208 10 false L198 5.177,3.542 5.656,3.75 0.479,0.208 10 false L199 5.167,4.01 5.646,4.219 0.479,0.208 10 false L199 5.281,0.917 5.76,1.125 0.479,0.208 10 false 1 5.271,1.385 5.75,1.594 0.479,0.208 10 false 2 5.281,3.333 5.76,3.542 0.479,0.208 10 false 1 5.271,3.813 5.75,4.021 0.479,0.208 10 false 2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L198 and L199 No. 4 CAN junction connectors.


c.

Measure the resistance according to the value(s) in the table below.

HINT:
·

Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.

·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C423692C14
0.792,1.104 0.969,1.104 0.969,1.104 1.323,1.354 true 0.844,1.719 1.031,1.719 1.031,1.719 1.323,1.563 true 0.542,0.656 0.854,0.854 0.313,0.198 10 false *a 0.448,1.667 1.052,1.875 0.604,0.208 10 false CANH 0.438,1.063 0.948,1.271 0.51,0.208 10 false CANL 2.781,0.646 3.094,0.844 0.313,0.198 10 false *b
*a Vehicle wire harness connector connected to CAN junction connector *b Rear view of wire harness connector
(to No. 4 CAN Junction Connector)


Standard Resistance:
Tester Connection Wiring Color Condition Specified Condition
L198-1 (CANH) - L198-2 (CANL) B - V Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L199-1 (CANH) - L199-2 (CANL) B - P Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

2.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Reconnect the L198 and L199 No. 4 CAN junction connectors.


b.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


c.
C354521C96
1.479,0.063 1.969,0.281 0.49,0.219 2.771,0.906 2.771,0.323 2.771,0.323 2.604,0.323 true 1.51,1.219 1.51,1.802 1.51,1.802 1.677,1.802 true 2.896,1.219 2.896,1.802 2.896,1.802 2.729,1.802 true 1.375,1.208 1.375,1.792 1.375,1.792 1.208,1.792 true 1.573,0.094 2.188,0.292 0.615,0.198 10 false L192 0.813,1.729 1.427,1.927 0.615,0.198 10 false CA5H 1.76,1.74 2.375,1.938 0.615,0.198 10 false CA5L 2.344,1.75 2.927,1.917 0.583,0.167 10 false CAXL 2.208,0.271 2.823,0.469 0.615,0.198 10 false CAXH 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L192-15 (CA5H) - L192-9 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
L192-16 (CA5L) - L192-24 (CAXL) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω




OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))