Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Front Camera Module Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode Either condition is met:
·

Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Front Camera Module Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Forward recognition camera branch line or connector

·

Power source circuit of forward recognition camera

·

Forward recognition camera ground circuit

·

Forward recognition camera



WIRING DIAGRAM

B423566E43
4.958,3.115 5.417,3.313 0.458,0.198 10 false U15 5.375,1.74 5.656,2 0.281,0.26 10 false 7 5.333,2.396 5.583,2.708 0.25,0.313 10 false 10 5.333,0.927 5.583,1.219 0.25,0.292 10 false 11 5.375,0.406 5.625,0.667 0.25,0.26 10 false 5 5.583,2.51 6.198,2.708 0.615,0.198 10 false GND 5.594,1.823 6.208,2.021 0.615,0.198 10 false IGB 5.573,0.51 6.188,0.708 0.615,0.198 10 false CA1P 5.583,1.031 6.198,1.229 0.615,0.198 10 false CA1N 5.26,3.115 7.063,3.417 1.802,0.302 10 false Forward Recognition Camera 0.51,1.417 2.688,1.656 2.177,0.24 10 false No. 4 CAN Junction Connector 0.167,1.417 0.49,1.74 0.323,0.323 10 false L185 1.49,0.927 1.74,1.188 0.25,0.26 10 false 2 1.479,0.406 1.729,0.667 0.25,0.26 10 false 1 1.708,1.823 3.854,2.021 2.146,0.198 10 false from IG1 NO. 1 Relay 3.865,2 4.844,2.229 0.979,0.229 10 false ECU-IG NO. 2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (FORWARD RECOGNITION CAMERA BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C325908C52
1.563,0.167 1.906,0.396 0.344,0.229 2,1.115 2,0.365 2,0.365 2.26,0.365 true 2,1.448 2,1.885 2,1.885 2.26,1.885 true 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 1.615,0.208 1.927,0.406 0.313,0.198 10 false U15 2.354,0.292 2.802,0.5 0.448,0.208 10 false CA1P 2.365,1.813 2.813,2.021 0.448,0.208 10 false CA1N
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the U15 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U15-5 (CA1P) - U15-11 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (FORWARD RECOGNITION CAMERA)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C325908C53
1.563,0.167 1.906,0.396 0.344,0.229 1.833,1.458 1.833,1.896 1.833,1.896 2.094,1.896 true 1.344,1.448 1.344,1.885 1.344,1.885 1.188,1.885 true 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 1.625,0.208 1.938,0.406 0.313,0.198 10 false U15 0.938,1.802 1.385,2.01 0.448,0.208 10 false IGB 2.198,1.813 2.646,2.021 0.448,0.208 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
U15-10 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U15-7 (IGB) - Body ground Power switch on (IG) 11 to 14 V




OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)