Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A11  Front Radar Sensor Incorrect Axial Gap  C1A14  Front Radar Sensor Beam Axis Not Adjusted  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect objects in front of the vehicle.

When it is determined that the vehicle is being driven in a straight line or on a gradual curve based on signals from the yaw rate and acceleration sensor, the millimeter wave radar sensor assembly performs self-diagnosis to check if the sensor beam axis has deviated. When the millimeter wave radar sensor assembly beam axis is misaligned, the driving support ECU assembly stores DTC C1A11.

After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A11 Front Radar Sensor Incorrect Axial Gap When the vehicle is being driven at a speed of 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.3 seconds or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


C1A14 Front Radar Sensor Beam Axis Not Adjusted When the vehicle is being driven at a speed of 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, incompletion of the millimeter wave radar sensor assembly beam axis alignment is detected for approximately 0.3 seconds or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

Check that the millimeter wave radar sensor assembly has not been replaced with one from another vehicle.

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If only history DTCs are stored, they may have been stored due to a temporary condition such as overloading of the vehicle.



PROCEDURE

1.CHECK FOR DTCs (RADAR CRUISE 2)
HINT:

If only history DTCs are stored, they may have been stored due to a temporary condition such as overloading of the vehicle.


a.

Check if the stored DTCs are current DTCs.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Body Electrical / Radar Cruise 2 / Trouble Codes.



Result:
Result Proceed to
Current DTC C1A11 is output A
Current DTC C1A14 is output B
History DTC C1A11 is output C



A

2.CHECK VEHICLE CONDITION

B

11.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

C

13.CLEAR DTC
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.



Result:
Result Proceed to
Vehicle is not overloaded or being towed A
Vehicle is overloaded or being towed B



A

3.CHECK WHEEL ALIGNMENT

B

9.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.CHECK WHEEL ALIGNMENT
a.

Check the front and rear wheel alignment (toe).

for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>INSPECTION

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).



Result:
Result Proceed to
Front or rear wheel is misaligned (toe) A
Front and rear wheels are not misaligned (toe) B



A

4.ADJUST WHEEL ALIGNMENT

B

7.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.ADJUST WHEEL ALIGNMENT
a.

Adjust the alignment (toe) of the wheels.

for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>INSPECTION


Result:
Proceed to
NEXT



NEXT

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (RADAR CRUISE 2)
6.CHECK FOR DTCs (RADAR CRUISE 2)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.





Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY

7.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that the bracket of the millimeter wave radar sensor assembly is not deformed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>INSTALLATION

HINT:

If the bracket is deformed, replace the millimeter wave radar sensor assembly with a new one.



Result:
Result Proceed to
Bracket is not deformed A
Bracket is deformed B



A

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
9.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Return the vehicle to normal operating conditions.


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTCs (RADAR CRUISE 2)
10.CHECK FOR DTCs (RADAR CRUISE 2)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.





Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END

B

3.CHECK WHEEL ALIGNMENT
11.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTCs (RADAR CRUISE 2)
12.CHECK FOR DTCs (RADAR CRUISE 2)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.





Result:
Result Proceed to
DTC C1A14 is not output A
DTC C1A14 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY

13.CLEAR DTC
a.

Check for DTCs related to misalignment of millimeter wave radar sensor assembly.



Result:
Proceed to
NEXT



NEXT

END