Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects in front of the vehicle to the driving support ECU assembly. The driving support ECU assembly sends this information to the hybrid vehicle control ECU and the hybrid vehicle control ECU operates the dynamic radar cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the millimeter wave radar sensor assembly and driving support ECU assembly is detected for approximately 1 second.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector


U1104 Lost Communication with Driving Support ECU While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the driving support ECU assembly and millimeter wave radar sensor assembly is detected for approximately 1 second.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

A409256E07
3.313,1.802 3.771,2 0.458,0.198 10 false U15 3.615,1.802 5.417,2.063 1.802,0.26 10 false Forward Recognition Camera 2.979,3.563 5.635,3.823 2.656,0.26 10 false Millimeter Wave Radar Sensor Assembly 2.99,3.375 3.448,3.573 0.458,0.198 10 false A91 3.531,5.385 5.677,5.625 2.146,0.24 10 false Driving Support ECU Assembly 1.021,5.26 3.167,5.5 2.146,0.24 10 false : CAN Communication Line 1.875,4.406 4.021,4.646 2.146,0.24 10 false ECU-IG NO. 2 4.5,4.865 5.146,5.135 0.646,0.271 10 false CA1N 3.167,5.396 3.813,5.667 0.646,0.271 10 false L205 4.5,4.156 5.146,4.427 0.646,0.271 10 false CA1P 4.51,2.99 5.156,3.26 0.646,0.271 10 false CA1P 4.5,2.406 5.146,2.677 0.646,0.271 10 false CA1N 4.469,1.313 5.115,1.583 0.646,0.271 10 false CANH 4.5,0.76 5.146,1.031 0.646,0.271 10 false CANL 4.135,0.729 4.781,1 0.646,0.271 10 false IGB 4.146,2.448 4.792,2.719 0.646,0.271 10 false IGB 4.146,4.219 4.792,4.49 0.646,0.271 10 false B 4.135,4.865 4.781,5.135 0.646,0.271 10 false GND 4.135,3.125 4.781,3.396 0.646,0.271 10 false SGND 4.135,1.396 4.781,1.667 0.646,0.271 10 false GND 3.958,0.625 4.604,0.896 0.646,0.271 10 false 7 3.896,1.292 4.542,1.563 0.646,0.271 10 false 10 4.938,0.604 5.583,0.875 0.646,0.271 10 false 12 4.958,1.135 5.604,1.406 0.646,0.271 10 false 6 4.938,2.229 5.583,2.5 0.646,0.271 10 false 6 4.938,2.813 5.583,3.083 0.646,0.271 10 false 5 3.979,2.354 4.625,2.625 0.646,0.271 10 false 8 3.979,3.021 4.625,3.292 0.646,0.271 10 false 1 3.969,4.094 4.615,4.365 0.646,0.271 10 false 7 3.906,4.76 4.552,5.031 0.646,0.271 10 false 28 4.948,4.667 5.594,4.938 0.646,0.271 10 false 9 4.938,3.99 5.583,4.26 0.646,0.271 10 false 8 0.01,0.698 2.156,0.938 2.146,0.24 10 false from IG1 NO. 1 Relay 0,4.188 2.146,4.427 2.146,0.24 10 false from IG1 NO. 1 Relay 1.865,0.885 4.01,1.125 2.146,0.24 10 false ECU-IG NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output OK
CAN communication system DTCs are output NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the L205 driving support ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L205-7 (B) - Body ground Power switch on (IG) 11 to 14 V
L205-7 (B) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
L205-28 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
A393386C15
1.5,0.177 1.896,0.417 0.396,0.24 0.875,1.583 1.417,1.063 true 2.458,1.625 1.948,1.208 true 0.094,0.115 0.406,0.271 0.313,0.156 10 false *a 0.469,1.552 1.083,1.75 0.615,0.198 10 false SGND 2.521,1.552 3.135,1.75 0.615,0.198 10 false IGB 1.583,0.229 2.198,0.427 0.615,0.198 10 false A91
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A91 millimeter wave radar sensor assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A91-8 (IGB) - Body ground Power switch on (IG) 11 to 14 V
A91-8 (IGB) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
A91-1 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the L205 driving support ECU assembly connector.


b.

Disconnect the A91 millimeter wave radar sensor assembly connector.


c.

Disconnect the U15 forward recognition camera connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L205-8 (CA1P) - A91-5 (CA1P) Always Below 1 Ω
L205-9 (CA1N) - A91-6 (CA1N) Always Below 1 Ω
L205-8 (CA1P) or A91-5 (CA1P) - Body ground Always 10 kΩ or higher
L205-9 (CA1N) or A91-6 (CA1N) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (RADAR CRUISE 2)
6.CHECK FOR DTCs (RADAR CRUISE 2)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.





Result:
Result Proceed to
DTC U0235 and U1104 are not output A
DTC U0235 or U1104 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY