Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2017.12
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the front passenger door only, but the entry lock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the touch sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [unlock sensor]).

WIRING DIAGRAM

B441774E06
1.302,0.729 1.688,0.885 0.385,0.156 10 false ANT1 1.281,1.177 1.677,1.333 0.396,0.156 10 false ANT2 0.198,3.448 1.583,3.823 1.385,0.375 10 false N16*1, O15*2 1.333,3.021 1.677,3.167 0.344,0.146 10 false GND 1.781,1.083 1.885,1.24 0.104,0.156 10 false 3 1.792,2.948 1.896,3.104 0.104,0.156 10 false 2 1.781,0.635 1.885,0.781 0.104,0.146 10 false 6 5.75,0.698 6.167,0.865 0.417,0.167 10 false CLG2 5.74,1.177 6.167,1.333 0.427,0.156 10 false CG2B 5.75,3.01 6.094,3.177 0.344,0.167 10 false E 5.406,0.521 5.615,0.677 0.208,0.156 10 false 11 5.427,0.99 5.646,1.156 0.219,0.167 10 false 10 1.542,1.635 1.677,1.792 0.135,0.156 10 false B 1.281,2.094 1.677,2.25 0.396,0.156 10 false SENS 1.781,2.01 1.885,2.167 0.104,0.156 10 false 4 1.781,1.563 1.885,1.708 0.104,0.146 10 false 5 5.75,1.625 6.167,1.792 0.417,0.167 10 false POS2 5.74,2.094 6.167,2.25 0.427,0.156 10 false SEN2 5.417,1.458 5.667,1.615 0.25,0.156 10 false 21 5.417,1.917 5.604,2.083 0.188,0.167 10 false 23 1.281,2.552 1.677,2.708 0.396,0.156 10 false TRG+ 1.781,2.479 1.885,2.635 0.104,0.156 10 false 1 5.74,2.563 6.167,2.719 0.427,0.156 10 false TSW2 5.458,2.385 5.646,2.552 0.188,0.167 10 false 8 5.417,2.833 5.615,3 0.198,0.167 10 false 11 5.365,3.469 7.063,4.021 1.698,0.552 10 false Certification ECU (Smart Key ECU Assembly) 0.198,3.615 1.927,4.344 1.729,0.729 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.344,0.708 5.74,0.875 0.396,0.167 10 false L197 5.344,3.021 5.802,3.24 0.458,0.219 10 false L195 3.021,4.031 4.292,4.188 1.271,0.156 10 false *1: for LHD 3.021,4.333 4.292,4.49 1.271,0.156 10 false *2: for RHD 5.344,1.177 5.74,1.344 0.396,0.167 10 false L197 5.344,1.635 5.74,1.802 0.396,0.167 10 false L197 5.344,2.104 5.74,2.271 0.396,0.167 10 false L197 5.344,2.563 5.74,2.729 0.396,0.167 10 false L197

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING GTS (UNLOCK DETECTION SWITCH)

NG

2.READ VALUE USING GTS (UNLOCK DETECTION SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FL Door Lock Pos*1 Front LH door unlock detection switch signal / UNLOCK or LOCK UNLOCK: Front LH door unlocked
LOCK: Front LH door locked
-
FR Door Lock Pos*2 Front RH door unlock detection switch signal / UNLOCK or LOCK UNLOCK: Front RH door unlocked
LOCK: Front RH door locked
-

*1: for RHD

*2: for LHD


OK:

On the GTS screen, the display changes between LOCK and UNLOCK as shown in the chart above.




OK

3.READ VALUE USING GTS (UNLOCK SENSOR)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

3.READ VALUE USING GTS (UNLOCK SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start or Main Body / Data List.


e.

Read the Data List according to the display on the GTS.


Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Door Touch Sensor Front passenger door touch sensor (unlock sensor) / ON or OFF ON: Front passenger door touch sensor (unlock sensor) touched
OFF: Front passenger door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.



OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger side).



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the N16*1 or O15*2 front door outside handle assembly (for front passenger door) connector.


b.

Disconnect the L195 and L197 certification ECU (smart key ECU assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
N16-4 (SENS) - L197-23 (SEN2) Always Below 1 Ω
L195-11 (E) - Body ground Always Below 1 Ω
N16-4 (SENS) or L197-23 (SEN2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
O15-4 (SENS) - L197-23 (SEN2) Always Below 1 Ω
L195-11 (E) - Body ground Always Below 1 Ω
O15-4 (SENS) or L197-23 (SEN2) - Body ground Always 10 kΩ or higher




OK

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (FRONT PASSENGER DOOR UNLOCK SENSOR SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (FRONT PASSENGER DOOR UNLOCK SENSOR SIGNAL INPUT)
a.

Connect the N16*1 or O15*2 front door outside handle assembly (for front passenger door) connector.

U190973E02
4.958,3.281 5.448,2.719 5.448,2.719 5.313,3.281 true 2.656,1.688 2.771,2.323 true 5,1.708 5.115,2.344 true 2.083,0.729 2.5,0.99 0.417,0.26 10 false L195 0.354,0.104 0.771,0.365 0.417,0.26 10 false *a 4.677,0.76 5.094,1.021 0.417,0.26 10 false L197 4.021,3.833 4.438,4.094 0.417,0.26 10 false GND 5.427,2.531 5.844,2.792 0.417,0.26 10 false *b 4.49,2.719 4.906,2.979 0.417,0.26 10 false *1 2.74,2.354 3.156,2.615 0.417,0.26 10 false E 4.958,2.354 5.375,2.615 0.417,0.26 10 false SEN2

Text in Illustration
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b In actuality, sampling is being performed

*1: for LHD

*2: for RHD



b.

Connect the L195 and L197 certification ECU (smart key ECU assembly) connectors.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
L197-23 (SEN2) - L195-11 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)