Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2017.12
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly (for front passenger door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [front passenger door electrical key antenna]), or there may be wave interference.

HINT:

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.


WIRING DIAGRAM

B441774E06
1.302,0.729 1.688,0.885 0.385,0.156 10 false ANT1 1.281,1.177 1.677,1.333 0.396,0.156 10 false ANT2 0.198,3.448 1.583,3.823 1.385,0.375 10 false N16*1, O15*2 1.333,3.021 1.677,3.167 0.344,0.146 10 false GND 1.781,1.083 1.885,1.24 0.104,0.156 10 false 3 1.792,2.948 1.896,3.104 0.104,0.156 10 false 2 1.781,0.635 1.885,0.781 0.104,0.146 10 false 6 5.75,0.698 6.167,0.865 0.417,0.167 10 false CLG2 5.74,1.177 6.167,1.333 0.427,0.156 10 false CG2B 5.75,3.01 6.094,3.177 0.344,0.167 10 false E 5.406,0.521 5.615,0.677 0.208,0.156 10 false 11 5.427,0.99 5.646,1.156 0.219,0.167 10 false 10 1.542,1.635 1.677,1.792 0.135,0.156 10 false B 1.281,2.094 1.677,2.25 0.396,0.156 10 false SENS 1.781,2.01 1.885,2.167 0.104,0.156 10 false 4 1.781,1.563 1.885,1.708 0.104,0.146 10 false 5 5.75,1.625 6.167,1.792 0.417,0.167 10 false POS2 5.74,2.094 6.167,2.25 0.427,0.156 10 false SEN2 5.417,1.458 5.667,1.615 0.25,0.156 10 false 21 5.417,1.917 5.604,2.083 0.188,0.167 10 false 23 1.281,2.552 1.677,2.708 0.396,0.156 10 false TRG+ 1.781,2.479 1.885,2.635 0.104,0.156 10 false 1 5.74,2.563 6.167,2.719 0.427,0.156 10 false TSW2 5.458,2.385 5.646,2.552 0.188,0.167 10 false 8 5.417,2.833 5.615,3 0.198,0.167 10 false 11 5.365,3.469 7.063,4.021 1.698,0.552 10 false Certification ECU (Smart Key ECU Assembly) 0.198,3.615 1.927,4.344 1.729,0.729 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.344,0.708 5.74,0.875 0.396,0.167 10 false L197 5.344,3.021 5.802,3.24 0.458,0.219 10 false L195 3.021,4.031 4.292,4.188 1.271,0.156 10 false *1: for LHD 3.021,4.333 4.292,4.49 1.271,0.156 10 false *2: for RHD 5.344,1.177 5.74,1.344 0.396,0.167 10 false L197 5.344,1.635 5.74,1.802 0.396,0.167 10 false L197 5.344,2.104 5.74,2.271 0.396,0.167 10 false L197 5.344,2.563 5.74,2.729 0.396,0.167 10 false L197

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

When the entry lock and unlock functions do not operate for doors other than the driver door and if the power switch has not been turned on (IG) for 14 days or more, lock/unlock the doors using the wireless door lock function or key linked unlock operation and then check if the entry door lock and unlock functions operate.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.CHECK WAVE ENVIRONMENT

NG

2.CHECK WAVE ENVIRONMENT
a.
B441721E01
0.117,0 0.467,0.345 0.350,0.345 12 *A 0.117,2.09 0.467,2.434 0.350,0.345 12 *B 1.818,1.127 2.169,1.472 0.350,0.345 10 *a 2.136,3.508 2.486,3.852 0.350,0.345 10 *a

Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for front passenger door) and perform an entry function check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

Text in Illustration
*A for LHD
*B for RHD
*a Approximately 0.3 m (0.984 ft.)

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.


Result:
Result Proceed to
Entry function does not operate normally. A
Entry function operates normally. B




A

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)

B

AFFECTED BY WAVE INTERFERENCE

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the N16*1, or O15*2 front door outside handle assembly (for front passenger door) connector.


b.

Disconnect the L197 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
N16-3 (ANT2) - L197-10 (CG2B) Always Below 1 Ω
N16-6 (ANT1) - L197-11 (CLG2) Always Below 1 Ω
N16-5 (B) - L197-21 (POS2) Always Below 1 Ω
N16-2 (GND) - Body ground Always Below 1 Ω
N16-3 (ANT2) or L197-10 (CG2B) - Body ground Always 10 kΩ or higher
N16-6 (ANT1) or L197-11 (CLG2) - Body ground Always 10 kΩ or higher
N16-5 (B) or L197-21 (POS2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
O15-3 (ANT2) - L197-10 (CG2B) Always Below 1 Ω
O15-6 (ANT1) - L197-11 (CLG2) Always Below 1 Ω
O15-5 (B) - L197-21 (POS2) Always Below 1 Ω
O15-2 (GND) - Body ground Always Below 1 Ω
O15-3 (ANT2) or L197-10 (CG2B) - Body ground Always 10 kΩ or higher
O15-6 (ANT1) or L197-11 (CLG2) - Body ground Always 10 kΩ or higher
O15-5 (B) or L197-21 (POS2) - Body ground Always 10 kΩ or higher




OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA)
a.
U190829E03
2.469,0.188 2.229,0.188 2.229,0.188 1.833,0.76 true 2.521,1.406 2.25,1.406 2.25,1.406 1.833,0.938 true 1.708,0.719 1.708,0.135 1.708,0.135 1.385,0.135 true 1.708,0.938 1.708,1.521 1.708,1.521 1.385,1.521 true 0.104,0.083 0.365,0.333 0.26,0.25 10 false *a 0.063,1.531 0.323,1.781 0.26,0.25 10 false *1 0.146,2.469 0.479,2.667 0.333,0.198 10 false GND 2.552,1.323 2.948,1.521 0.396,0.198 10 false ANT1 0.448,0.927 0.813,1.094 0.365,0.167 10 false O15 2.521,0.104 2.938,0.25 0.417,0.146 10 false ANT2 0.458,0.521 0.865,0.688 0.406,0.167 10 false N16 0.885,0.51 1.063,0.677 0.177,0.167 10 false *A 0.885,0.917 1.063,1.083 0.177,0.167 10 false *B 1.25,1.448 1.396,1.615 0.146,0.167 10 false B 1.052,0.052 1.427,0.219 0.375,0.167 10 false GND

Disconnect the N16*1 or O15*2 front door outside handle assembly (for front passenger door) connector.


b.

Connect the L197 certification ECU (smart key ECU assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N16-5 (B) - N16-2 (GND)*1
O15-5 (B) - O15-2 (GND)*2
Power switch off → on (IG) 9 to 14 V → Below 2 V



d.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
N16-3 (ANT2) - N16-6 (ANT1)*1
O15-3 (ANT2) - O15-6 (ANT1)*2
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)


*1: for LHD

*2: for RHD


Text in Illustration
*A for LHD
*B for RHD
*1 Waveform
*a Front view of wire harness connector
(to Front Door Outside handle assembly (for front passenger door))



OK

5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
a.

Temporarily replace the front door outside handle assembly (for front passenger door) with a new or known good one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
a.

Check that the entry functions operate normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Entry functions operate normally.




OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)