Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2017.12
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger door) [electrical key antenna] at intervals of 0.25 seconds. For the front door outside handle assembly (for front passenger door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the front passenger door at intervals of 0.25 seconds. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [electrical key antenna] (between terminals CLG2 and ANT1, or terminals CG2B and ANT2).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A2 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (CLG2 - ANT1, CG2B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Wire harness or connector

·

Front door outside handle assembly (for front passenger door)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A2 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B441774E06
1.302,0.729 1.688,0.885 0.385,0.156 10 false ANT1 1.281,1.177 1.677,1.333 0.396,0.156 10 false ANT2 0.198,3.448 1.583,3.823 1.385,0.375 10 false N16*1, O15*2 1.333,3.021 1.677,3.167 0.344,0.146 10 false GND 1.781,1.083 1.885,1.24 0.104,0.156 10 false 3 1.792,2.948 1.896,3.104 0.104,0.156 10 false 2 1.781,0.635 1.885,0.781 0.104,0.146 10 false 6 5.75,0.698 6.167,0.865 0.417,0.167 10 false CLG2 5.74,1.177 6.167,1.333 0.427,0.156 10 false CG2B 5.75,3.01 6.094,3.177 0.344,0.167 10 false E 5.406,0.521 5.615,0.677 0.208,0.156 10 false 11 5.427,0.99 5.646,1.156 0.219,0.167 10 false 10 1.542,1.635 1.677,1.792 0.135,0.156 10 false B 1.281,2.094 1.677,2.25 0.396,0.156 10 false SENS 1.781,2.01 1.885,2.167 0.104,0.156 10 false 4 1.781,1.563 1.885,1.708 0.104,0.146 10 false 5 5.75,1.625 6.167,1.792 0.417,0.167 10 false POS2 5.74,2.094 6.167,2.25 0.427,0.156 10 false SEN2 5.417,1.458 5.667,1.615 0.25,0.156 10 false 21 5.417,1.917 5.604,2.083 0.188,0.167 10 false 23 1.281,2.552 1.677,2.708 0.396,0.156 10 false TRG+ 1.781,2.479 1.885,2.635 0.104,0.156 10 false 1 5.74,2.563 6.167,2.719 0.427,0.156 10 false TSW2 5.458,2.385 5.646,2.552 0.188,0.167 10 false 8 5.417,2.833 5.615,3 0.198,0.167 10 false 11 5.365,3.469 7.063,4.021 1.698,0.552 10 false Certification ECU (Smart Key ECU Assembly) 0.198,3.615 1.927,4.344 1.729,0.729 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.344,0.708 5.74,0.875 0.396,0.167 10 false L197 5.344,3.021 5.802,3.24 0.458,0.219 10 false L195 3.021,4.031 4.292,4.188 1.271,0.156 10 false *1: for LHD 3.021,4.333 4.292,4.49 1.271,0.156 10 false *2: for RHD 5.344,1.177 5.74,1.344 0.396,0.167 10 false L197 5.344,1.635 5.74,1.802 0.396,0.167 10 false L197 5.344,2.104 5.74,2.271 0.396,0.167 10 false L197 5.344,2.563 5.74,2.729 0.396,0.167 10 false L197

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The front door outside handle assembly (for front passenger door) has an antenna coil between ANT1 and ANT2 terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)
a.

Disconnect the L195 and L197 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the N16*1 or O15*2 front door outside handle assembly (for front passenger door) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L197-11 (CLG2) - N16-6 (ANT1) Always Below 1 Ω
L197-10 (CG2B) - N16-3 (ANT2) Always Below 1 Ω
L195-11 (E) - Body ground Always Below 1 Ω
N16-2 (GND) - Body ground Always Below 1 Ω
L197-11 (CLG2) or N16-6 (ANT1) - Body ground Always 10 kΩ or higher
L197-10 (CG2B) or N16-3 (ANT2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
L197-11 (CLG2) - O15-6 (ANT1) Always Below 1 Ω
L197-10 (CG2B) - O15-3 (ANT2) Always Below 1 Ω
L195-11 (E) - Body ground Always Below 1 Ω
O15-2 (GND) - Body ground Always Below 1 Ω
L197-11 (CLG2) or O15-6 (ANT1) - Body ground Always 10 kΩ or higher
L197-10 (CG2B) or O15-3 (ANT2) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA)
a.

Connect the L195 and L197 certification ECU (smart key ECU assembly) connectors.

U190851E02
2.708,1.51 2.51,2.063 2.51,2.063 2.26,2.063 true 5.177,1.406 5.458,2.375 5.458,2.375 5.76,2.375 true 5.104,1.406 4.823,2.375 4.823,2.375 4.521,2.375 true 0.198,0.146 0.417,0.344 0.219,0.198 10 false *a 1.208,2.823 1.427,3.021 0.219,0.198 10 false *1 0.969,3.635 1.333,3.802 0.365,0.167 10 false GND 3.854,3.635 4.219,3.802 0.365,0.167 10 false GND 4.146,2.823 4.365,3.021 0.219,0.198 10 false *2 2.156,1.979 2.292,2.146 0.135,0.167 10 false E 5.781,2.302 6.177,2.469 0.396,0.167 10 false CG2B 4.135,2.292 4.531,2.458 0.396,0.167 10 false CLG2 2.188,0.646 2.708,0.885 0.521,0.24 10 false L195 4.802,0.656 5.135,0.823 0.333,0.167 10 false L197

Text in Illustration
*1 Waveform 1 *2 Waveform 2
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
- -


b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
L197-11 (CLG2) - L195-11 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)
L197-11 (CLG2) - L195-11 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)
L197-10 (CG2B) - L195-11 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)


*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).




OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
a.

Temporarily replace the front door outside handle assembly (for front passenger door) with a new or known good one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)