Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › from 2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM C

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  C1628  Vehicle Height Sensor Failure  


DESCRIPTION

The rear height control sensor sub-assembly RH is connected to the parking assist ECU. This DTC is stored when the parking assist ECU judges that vehicle height sensor signal received from the rear height control sensor sub-assembly RH is abnormal or has not changed (rear height control sensor sub-assembly RH seized).

DTC No. DTC Detection Condition Trouble Area
C1628
·

Height control sensor signal is abnormal

·

Height control sensor seized


·

Harness or connector

·

Rear height control sensor sub-assembly RH

·

Parking assist ECU



WIRING DIAGRAM

E449814E01
0.438,1.917 0.792,2.073 0.354,0.156 10 false S25 1.979,0.25 2.115,0.406 0.135,0.156 10 false 3 1.979,0.885 2.115,1.042 0.135,0.156 10 false 2 1.979,1.469 2.115,1.625 0.135,0.156 10 false 1 5.125,0.885 5.313,1.042 0.188,0.156 10 false 9 5.042,1.469 5.24,1.625 0.198,0.156 10 false 31 1.573,0.365 1.885,0.521 0.313,0.156 10 false SHB 1.563,1.552 1.885,1.708 0.323,0.156 10 false SHG 1.479,0.958 1.896,1.115 0.417,0.156 10 false SHRR 5.302,1.552 5.625,1.708 0.323,0.156 10 false HG1 5.302,0.958 5.719,1.115 0.417,0.156 10 false HI1 0.427,2.083 2.115,2.531 1.688,0.448 10 false Rear Height Control Sensor Sub-assembly RH 5.24,1.927 5.656,2.125 0.417,0.198 10 false L65 5.24,2.094 7.063,2.281 1.823,0.188 10 false Parking Assist ECU 5.063,0.313 5.26,0.49 0.198,0.177 10 false 27 5.281,0.396 5.917,0.573 0.635,0.177 10 false HBL+

CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the navigation receiver assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH)
a.

Disconnect the L65 parking assist ECU connector.


b.

Disconnect the S25 rear height control sensor sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-27 (HBL+) - Body ground Always 10 kΩ or higher
L65-9 (HI1) - Body ground Always 10 kΩ or higher
L65-31 (HG1) - Body ground Always 10 kΩ or higher
L65-27 (HBL+) - S25-3 (SHB) Always Below 1 Ω
L65-9 (HI1) - S25-2 (SHRR) Always Below 1 Ω
L65-31 (HG1) - S25-1 (SHG) Always Below 1 Ω


Result:
Result Proceed to
NG A
OK B




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

2.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH
2.CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH
a.

Reconnect the L65 parking assist ECU connector.


b.

Disconnect the S25 rear height control sensor sub-assembly RH connector.


c.
U191342E02
1.896,1.51 2.542,1.51 false 0.906,1.51 1.552,1.51 false 1.604,0.24 1.875,0.417 0.271,0.177 10 false S25 2.583,1.438 3.177,1.625 0.594,0.188 10 false SHB 0.573,1.427 1.167,1.615 0.594,0.188 10 false SHG 0.135,0.063 0.729,0.25 0.594,0.188 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S25-3 (SHB) - S25-1 (SHG) Power switch on (IG) 4.75 to 5.25 V


Text in Illustration
*a Front view of wire harness connector
(to Rear Height Control Sensor Sub-assembly RH)



OK

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

NG