Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2020.08
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

Condition 1:
·

When the brakes are applied by the dynamic radar cruise control system, the skid control ECU (brake booster with master cylinder assembly) operates the stop light switch assembly (stop light control relay) to illuminate the stop lights.

If the hybrid vehicle control ECU receives a stop light control relay malfunction signal from the skid control ECU (brake booster with master cylinder assembly), DTC P0571 is stored.


Condition 2:
·

When the brake pedal is depressed, the stop light switch assembly sends a signal to the hybrid vehicle control ECU. When the hybrid vehicle control ECU receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to the terminal STP. When the brake is applied, voltage is normally applied to the terminal STP of the hybrid vehicle control ECU through the STOP fuse and stop light switch assembly, and the hybrid vehicle control ECU turns the dynamic radar cruise control system off.


DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit
Condition 1:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU detects the stop light control relay error signal from the skid control ECU for approximately 0.5 seconds or more.


Condition 2:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, voltage of the STP terminal and that of the ST1- terminal of the hybrid vehicle control ECU are less than 1 V for approximately 0.5 seconds or more.


Condition 1:
·

Pre-crash safety system


Condition 2:
·

Stop light switch assembly

·

Hybrid vehicle control ECU

·

Harness or connector



WIRING DIAGRAM

A415046E06
0.333,0.865 2.021,1.063 1.688,0.198 10 false from DC/DC Fuse 0.5,1.344 2.188,1.542 1.688,0.198 10 false from IG2 Relay 2.406,1.052 4.094,1.25 1.688,0.198 10 false STOP 2.469,1.521 4.156,1.719 1.688,0.198 10 false IGN 3.042,2.26 4.729,2.458 1.688,0.198 10 false A93 3.375,2.26 4.531,2.74 1.156,0.479 10 false Stop Light Switch Assembly 3.375,0.76 3.729,1.073 0.354,0.313 10 false 7 3.385,1.271 3.74,1.583 0.354,0.313 10 false 6 3.385,1.781 3.74,2.094 0.354,0.313 10 false 2 4.354,0.656 4.708,0.969 0.354,0.313 10 false 3 4.344,1.427 4.698,1.74 0.354,0.313 10 false 5 3.573,0.896 3.927,1.208 0.354,0.313 10 false B 3.573,1.385 3.927,1.698 0.354,0.313 10 false B 3.573,1.906 3.927,2.219 0.354,0.313 10 false GND 4.167,0.76 4.521,1.073 0.354,0.313 10 false L 4.156,1.563 4.51,1.875 0.354,0.313 10 false L 5.781,2.25 6.719,2.656 0.938,0.406 10 false Hybrid Vehicle Control ECU 5.281,1.552 5.781,1.813 0.5,0.26 10 false A22 5.281,0.75 5.781,1.01 0.5,0.26 10 false A21 5.323,0.552 5.823,0.813 0.5,0.26 10 false 15 5.323,1.344 5.823,1.604 0.5,0.26 10 false 28 5.677,0.667 6.177,0.927 0.5,0.26 10 false STP 5.677,1.448 6.177,1.708 0.5,0.26 10 false ST1- 3.198,3.771 5.281,4.167 2.083,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.885,3.771 4.573,3.969 1.688,0.198 10 false A58 3.927,3.406 5.615,3.604 1.688,0.198 10 false STP2 4.365,3.292 6.052,3.49 1.688,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Check for DTCs of the pre-crash safety system.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

HINT:

When DTC P0571 is stored by the dynamic radar cruise control system, DTC C1A4B may be stored by the pre-crash safety system. Therefore, if DTC P0571 is stored, inspect the pre-crash safety system first.



Result:
Result Proceed to
DTC C1A4B is output A
DTC C1A4B is not output B



A

GO TO PRE-CRASH SAFETY SYSTEM

B

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
C439920C05
1.479,0.302 1.875,0.521 0.396,0.219 0.938,1.844 1.396,1.25 true 1.542,1.844 1.969,1.25 true 2.188,1.135 2.656,0.49 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.802,1.875 1.26,2.073 0.458,0.198 10 false GND 1.51,1.875 1.969,2.073 0.458,0.198 10 false B 2.74,0.385 3.198,0.583 0.458,0.198 10 false B 1.563,0.323 2.021,0.521 0.458,0.198 10 false A93
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A93 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A93-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A93-7 (B) - Body ground Power switch off 11 to 14 V
A93-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A93-6 (B) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A21 and A22 hybrid vehicle control ECU connector.


b.

Disconnect the A93 stop light switch assembly connector.


c.

Disconnect the A58 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-28 (ST1-) - A93-5 (L) Always Below 1 Ω
A21-15 (STP) - A93-3 (L) Always Below 1 Ω
A22-28 (ST1-) or A93-5 (L) - Body ground Always 10 kΩ or higher
A21-15 (STP) or A93-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR