These DTCs are stored when the combination meter sub-assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1507 | When IG voltage is 9.5 V or more and the following condition is detected:
1.
Open in turn signal light circuit |
·
Bulb ·
Harness or connector ·
Instrument panel junction block assembly ·
Combination meter sub-assembly |
| B1508 | When IG voltage is 9.5 V or more and the following condition is detected:
1.
Short in turn signal light circuit or hazard warning light circuit |
·
Bulb ·
Harness or connector ·
Instrument panel junction block assembly ·
Combination meter sub-assembly |
Inspect the bulbs for this system before performing the following inspection procedure.
Inspect the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| Turn signal lights for one side do not illuminate | A |
| Front turn signal light does not illuminate | B |
| Rear turn signal light does not illuminate | C |
| Side turn signal light does not illuminate | D |
A
B
C
D
Disconnect the L125 combination meter sub-assembly connector.
Disconnect the 2A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L125-3 (LL) - 2A-22 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L125-5 (LR) - 2A-17 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L125-3 (LL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L125-5 (LR) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
for Halogen headlight type
Disconnect the A77*1 or A82*2 front turn signal light connector.
*1: for LH
*2: for RH
Disconnect the 2C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A77-3 - 2C-17 | Always | Below 1 Ω |
| A77-2 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A82-3 - 2C-36 | Always | Below 1 Ω |
| A82-2 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A77-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A82-3 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
for LED headlight type
Disconnect the A85*1 or A87*2 front turn signal light connector.
*1: for LH
*2: for RH
Disconnect the 2C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A85-5 - 2C-17 | Always | Below 1 Ω |
| A85-6 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A87-5 - 2C-36 | Always | Below 1 Ω |
| A87-6 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A85-5 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A87-5 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the R17*1 or S18*2 rear turn signal light connector.
*1: for LH
*2: for RH
Disconnect the 2D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R17-6 (B) - 2D-17 | Always | Below 1 Ω |
| R17-5 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S18-6 (B) - 2D-4 | Always | Below 1 Ω |
| S18-5 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R17-6 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S18-6 (B) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the O12*1 or N12*2 outer rear view mirror assembly connector.
*1: for LH
*2: for RH
Disconnect the 2B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O12-2 (B) - 2B-35 | Always | Below 1 Ω |
| O12-9 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N12-2 (B) - 2B-37 | Always | Below 1 Ω |
| N12-9 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O12-2 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N12-2 (B) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2A-22 - 2C-17 | Always | Below 1 Ω |
| 2A-22 - 2D-17 | Always | Below 1 Ω |
| 2A-22 - 2B-35 | Always | Below 1 Ω |
| 2A-17 - 2C-36 | Always | Below 1 Ω |
| 2A-17 - 2D-4 | Always | Below 1 Ω |
| 2A-17 - 2B-37 | Always | Below 1 Ω |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
OK
NG