The combination meter sub-assembly receives the vehicle speed signal from the skid control ECU via the CAN communication system. The speed sensors detect the wheel speed and send signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensors. The skid control ECU creates the vehicle speed signal based on the pulses of the voltage.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores DTCs. Troubleshoot the brake control system (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
Before starting the following inspection, check the tire size and tire air pressure.
Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output | A |
| CAN communication DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Speed Meter Operation | Speedometer | 0, 40, 80 or 120 | Unit: mph |
| 0, 40, 80, 120 or 160 | Unit: km/h |
Speedometer indication is normal.
OK
NG
Check if the electronically controlled brake system outputs DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus:
for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Data List.
for Combination Meter: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed | Maximum wheel speed sensor/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
When the Data List values of the ECUs match, an internal malfunction of the combination meter sub-assembly is suspected.
When the Data List values of the ECUs do not match, a signal output error of the skid control ECU or an internal malfunction of the combination meter sub-assembly is suspected.
| Result | Proceed to |
|---|---|
| The data list values of the ECUs match | A |
| The data list values of the ECUs do not match | B |
A
B
Replace the combination meter sub-assembly with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).
The operation of the speedometer returns to normal.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output (for LHD) | B |
| DTCs are output (for RHD) | C |
A
B
C