Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The combination meter sub-assembly uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 15 Ω with the float at the full position, and 410 Ω with the float at the empty position. The meter outputs auxiliary battery voltage through two resistors that are mounted inside the combination meter sub-assembly. The combination meter sub-assembly measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the auxiliary battery voltage.


HINT:

The fuel level warning light will come on when the fuel level is below 6.0 liters (6.3 US qts, 5.2 Imp. qts).


WIRING DIAGRAM

E230580E55
4.958,3.104 7.146,3.458 2.188,0.354 10 false Combination Meter Sub-assembly 5.719,0.979 5.99,1.135 0.271,0.156 10 false L 5.719,2.344 6.125,2.5 0.406,0.156 10 false ES 2 5.479,0.885 5.938,1.271 0.458,0.385 10 false 12 5.469,2.24 5.823,2.583 0.354,0.344 10 false 13 2.323,2.229 2.438,2.375 0.115,0.146 10 false 3 2.323,0.885 2.438,1.031 0.115,0.146 10 false 2 0.656,3.135 4.771,3.313 4.115,0.177 10 false Fuel Sender Gauge Assembly 0.781,1.448 1.219,1.615 0.438,0.167 10 false Fuel 2.031,2.229 2.281,2.406 0.25,0.177 10 false FE 2.042,0.885 2.344,1.177 0.302,0.292 10 false FS 4.969,2.938 5.479,3.271 0.51,0.333 10 false L27 0.656,2.979 1.333,3.333 0.677,0.354 10 false R11 1.698,2.01 1.813,2.156 0.115,0.146 10 false 1 1.688,1.354 1.802,1.5 0.115,0.146 10 false 2 0.771,1.625 1.313,1.802 0.542,0.177 10 false Sender 0.771,1.792 1.271,2 0.5,0.208 10 false Gauge 0.771,1.948 1.49,2.146 0.719,0.198 10 false Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F -

OK:

Fuel receiver gauge indication is normal.




OK

2.READ VALUE USING GTS (FUEL INPUT)

NG

REPLACE COMBINATION METER SUB-ASSEMBLY

2.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0, Max.: 127.5 10th segment comes on:
39.8 to 45.0
Unit: Liter
9th segment comes on:
36.2 to 39.8
8th segment comes on:
32.6 to 36.2
7th segment comes on:
28.6 to 32.6
6th segment comes on:
24.4 to 28.6
5th segment comes on:
20.1 to 24.4
4th segment comes on:
16.0 to 20.1
3rd segment comes on:
12.5 to 16.0
2nd segment comes on:
8.6 to 12.5
1st segment comes on:
4.8 to 8.6

Result:
Result Proceed to
Fuel level displayed on the GTS is almost the same as fuel receiver gauge indication A
Fuel level displayed on the GTS differs from the fuel receiver gauge indication B




A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY)

B

REPLACE COMBINATION METER SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the R11 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-12 (L) - R11-2 (FS) Always Below 1 Ω
L27-13 (ES 2) - R11-3 (FE) Always Below 1 Ω
L27-12 (L) - Body ground Always 10 kΩ or higher
L27-13 (ES 2) - Body ground Always 10 kΩ or higher




OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Inspect the fuel sender gauge assembly (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION).



OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG