Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 3 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Navigation receiver assembly

·

No. 6 CAN junction connector



WIRING DIAGRAM

C351110E12
1.438,1.208 1.75,1.406 0.313,0.198 10 false 21 1.438,0.74 1.75,0.938 0.313,0.198 10 false 6 3.708,0.74 4.021,0.938 0.313,0.198 10 false 5 3.635,1.219 3.948,1.417 0.313,0.198 10 false 16 4.802,2.771 5.115,2.969 0.313,0.198 10 false 7 5.771,3.25 6.083,3.448 0.313,0.198 10 false 10 4.74,3.26 5.052,3.458 0.313,0.198 10 false 18 3.698,4.865 4.01,5.063 0.313,0.198 10 false 6 1.417,4.854 1.729,5.052 0.313,0.198 10 false 19 3.635,5.344 3.948,5.542 0.313,0.198 10 false 17 1.427,5.333 1.74,5.531 0.313,0.198 10 false 20 0.917,0.74 1.333,0.958 0.417,0.219 10 false CA3H 0.938,1.229 1.354,1.448 0.417,0.219 10 false CA3L 0.344,1.083 0.76,1.302 0.417,0.219 10 false 120 Ω 0.885,4.875 1.344,5.073 0.458,0.198 10 false CAYH 0.927,5.354 1.385,5.552 0.458,0.198 10 false CAYL 0.344,5.198 0.76,5.417 0.417,0.219 10 false 120 Ω 5.833,2.771 6.146,2.969 0.313,0.198 10 false 9 6.083,2.885 6.563,3.125 0.479,0.24 10 false CANH 6.083,3.375 6.563,3.615 0.479,0.24 10 false CANL 3.177,5.844 3.604,6.063 0.427,0.219 10 false L204 3.552,5.844 5.979,6.125 2.427,0.281 10 false No. 6 CAN Junction Connector 0.083,5.875 0.802,6.135 0.719,0.26 10 false L192 0.448,5.875 2.396,6.313 1.948,0.438 10 false Central Gateway ECU (Network Gateway ECU) 5.74,3.865 6.948,4.385 1.208,0.521 10 false Navigation Receiver Assembly 5.396,3.865 5.75,4.073 0.354,0.208 10 false L38

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L204 No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C421985C33
3.646,1.333 4.083,1.563 0.438,0.229 0.271,1.375 0.708,1.604 0.438,0.229 1.708,0.677 1.875,0.677 1.875,0.677 1.875,1.427 true 1.719,2.188 1.885,2.188 1.885,2.188 1.885,1.688 true 1.885,2.448 2.052,2.448 2.052,2.448 2.052,1.698 true 1.885,0.417 2.052,0.417 2.052,0.417 2.052,1.417 true 6.104,2.135 5.938,2.135 5.938,2.135 5.938,1.719 true 2.375,0.688 2.208,0.688 2.208,0.688 2.208,1.438 true 2.385,2.198 2.219,2.198 2.219,2.198 2.219,1.698 true 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.719,0.188 4.031,0.385 0.313,0.198 10 false *1 3.76,1.365 4.135,1.563 0.375,0.198 10 false L61 0.313,1.417 0.688,1.615 0.375,0.198 10 false L204 1.115,0.594 1.75,0.833 0.635,0.24 10 false CANH*b 1.198,2.104 1.833,2.344 0.635,0.24 10 false CANL*b 1.354,2.365 1.99,2.604 0.635,0.24 10 false CANL*b 1.333,0.333 1.969,0.573 0.635,0.24 10 false CANH*b 6.177,2.063 6.552,2.26 0.375,0.198 10 false BAT 2.458,0.615 3.427,1.052 0.969,0.438 10 false CANH*c 2.49,2.115 3.26,2.396 0.771,0.281 10 false CANL*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Navigation Receiver Assembly - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L204-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
L204-16 (CANL) - L61-16 (BAT)
L204-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
L204-17 (CANL) - L61-16 (BAT)
L204-7 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Navigation receiver assembly
L204-18 (CANL) - L61-16 (BAT)


Result:
Symptom Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C




A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C385980C71
3.646,1.333 4.083,1.563 0.438,0.229 0.271,1.375 0.708,1.604 0.438,0.229 1.708,0.677 1.875,0.677 1.875,0.677 1.875,1.427 true 1.719,2.188 1.885,2.188 1.885,2.188 1.885,1.688 true 6.104,2.135 5.938,2.135 5.938,2.135 5.938,1.719 true 2.219,0.688 2.052,0.688 2.052,0.688 2.052,1.438 true 2.219,2.198 2.052,2.198 2.052,2.198 2.052,1.698 true 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.719,0.188 4.031,0.385 0.313,0.198 10 false *1 3.76,1.365 4.135,1.563 0.375,0.198 10 false L61 0.333,1.406 0.708,1.604 0.375,0.198 10 false L204 1.115,0.594 1.75,0.833 0.635,0.24 10 false CANH*b 1.198,2.104 1.833,2.344 0.635,0.24 10 false CANL*b 2.281,2.115 2.917,2.354 0.635,0.24 10 false CANL*b 2.313,0.604 2.948,0.844 0.635,0.24 10 false CANH*b 6.177,2.063 6.552,2.26 0.375,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
L204-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L204-16 (CANL) - L61-16 (BAT)
L204-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L204-17 (CANL) - L61-16 (BAT)




OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU).


c.

Measure the resistance according to the value(s) in the table below.

C351275C84
1.604,0.198 2.094,0.448 0.49,0.25 4.938,0.292 5.354,0.563 0.417,0.271 1.5,1.229 1.5,0.625 1.5,0.625 1.365,0.625 true 1.385,2.104 1.521,2.104 1.521,2.104 1.521,1.406 true 6.021,2.156 5.854,2.156 5.854,2.156 5.854,1.677 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.698,0.25 2.302,0.469 0.604,0.219 10 false L192 0.969,0.552 1.521,0.75 0.552,0.198 10 false CA3H 6.135,2.083 6.688,2.281 0.552,0.198 10 false BAT 0.99,2.031 1.542,2.229 0.552,0.198 10 false CA3L 5.042,0.354 5.354,0.552 0.313,0.198 10 false L61 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
L192-6 (CA3H) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-21 (CA3L) - L61-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.





OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR