Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Clock Malfunction  


DESCRIPTION

The combination meter sub-assembly and the hazard warning signal switch assembly are connected via direct line. The clock adjusted using the clock switches of the hazard warning signal switch assembly.

WIRING DIAGRAM

E449750E04
1.823,0.823 2.438,1.021 0.615,0.198 10 false HOUR 1.958,1.313 2.573,1.51 0.615,0.198 10 false MIN 1.938,1.833 2.552,2.031 0.615,0.198 10 false RST 2.104,2.344 2.719,2.542 0.615,0.198 10 false E 2.365,0.823 2.979,1.021 0.615,0.198 10 false 6 2.354,1.313 2.969,1.51 0.615,0.198 10 false 7 2.354,1.833 2.969,2.031 0.615,0.198 10 false 8 2.344,2.344 2.958,2.542 0.615,0.198 10 false 5 1.5,1.135 2.115,1.333 0.615,0.198 10 false H 1.479,1.625 2.094,1.823 0.615,0.198 10 false M 1.417,2.135 2.031,2.333 0.615,0.198 10 false : 00 4.688,0.823 5.302,1.021 0.615,0.198 10 false 21 4.677,1.333 5.292,1.531 0.615,0.198 10 false 22 4.688,1.833 5.302,2.031 0.615,0.198 10 false 23 4.99,0.823 5.604,1.021 0.615,0.198 10 false HOUR 4.99,1.333 5.604,1.531 0.615,0.198 10 false MIN 4.979,1.823 5.594,2.021 0.615,0.198 10 false RST 5.781,0.469 6.396,0.667 0.615,0.198 10 false 12 V 0.74,3.01 1.354,3.208 0.615,0.198 10 false L57 0.729,3.198 4.281,3.583 3.552,0.385 10 false Hazard Warning Signal Switch Assembly 4.844,2.615 5.458,2.813 0.615,0.198 10 false L27 4.833,2.802 6.906,3.094 2.073,0.292 10 false Combination Meter Sub-assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Timer Switch M on Combination Meter Minute adjust switch / OFF or ON OFF: Minute adjust switch not pushed -
ON: Minute adjust switch pushed -
Timer Switch H on Combination Meter Hour adjust switch / OFF or ON OFF: Hour adjust switch not pushed -
ON: Hour adjust switch pushed -
Timer Switch 00 on Combination Meter Second adjust switch / OFF or ON OFF: Second adjust switch not pushed -
ON: Second adjust switch pushed -


Result:
Result Proceed to
The Data List item changes correctly A
The Data List item do not change correctly B



A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
a.

Remove the hazard warning signal switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>REMOVAL


b.

Inspect the hazard warning signal switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)

NG

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L57-6 (HOUR) - L27-21 (HOUR) Always Below 1 Ω
L57-7 (MIN) - L27-22 (MIN) Always Below 1 Ω
L57-8 (RST) - L27-23 (RST) Always Below 1 Ω
L57-6 (HOUR) or L27-21 (HOUR) - Body ground Always 10 kΩ or higher
L57-7 (MIN) or L27-22 (MIN) - Body ground Always 10 kΩ or higher
L57-8 (RST) or L27-23 (RST) - Body ground Always 10 kΩ or higher
L57-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR