Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2020.08
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the EPS warning light.

WIRING DIAGRAM

U191214E02
1.25,1.177 1.427,1.333 0.177,0.156 10 false 13 0.948,1.281 1.146,1.438 0.198,0.156 10 false TC 4.177,0.542 4.354,0.698 0.177,0.156 10 false 24 3.646,0.708 4.031,0.865 0.385,0.156 10 false CA1L 4.177,1.938 4.365,2.094 0.188,0.156 10 false 25 3.625,2.094 4.042,2.25 0.417,0.156 10 false CA1H 5.958,0.708 6.344,0.865 0.385,0.156 10 false CANL 5.76,0.552 5.854,0.708 0.094,0.156 10 false 7 5.76,1.938 5.854,2.094 0.094,0.156 10 false 1 5.958,2.094 6.375,2.25 0.417,0.156 10 false CANH 1.26,1.917 1.438,2.073 0.177,0.156 10 false 4 0.927,2.021 1.156,2.177 0.229,0.156 10 false CG 0.406,2.74 0.656,2.896 0.25,0.156 10 false L61 0.729,2.74 1.104,2.896 0.375,0.156 10 false DLC3 3.229,2.771 4.844,3.115 1.615,0.344 10 false Hybrid Vehicle Control ECU Assembly 5.813,2.781 6.781,3.115 0.969,0.333 10 false Power Steering ECU Assembly 5.5,2.781 5.75,2.958 0.25,0.177 10 false L54 3.292,1.281 3.5,1.438 0.208,0.156 10 false TC 3,2.781 3.177,2.938 0.177,0.156 10 false L6 3.052,1.167 3.292,1.344 0.24,0.177 10 false 28

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-13 (TC) - L6-28 (TC) Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
U191005E02
1.677,1.958 2.406,1.01 true 0.271,0.25 0.458,0.417 0.188,0.167 10 false *a 2.365,0.813 2.604,0.979 0.24,0.167 10 false CG 0.281,1.042 0.531,1.188 0.25,0.146 10 false L61

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of DLC3



OK

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)
a.
U191006E02
1.854,2.396 2.583,0.958 true 0.271,0.25 0.458,0.417 0.188,0.167 10 false *a 2.531,0.802 2.771,0.969 0.24,0.167 10 false TC 0.292,1.042 0.542,1.188 0.25,0.146 10 false L61

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-13 (TC) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of DLC3

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS OR EACH ECU