Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  



FUNCTION OF SRS WARNING LIGHT


a.

Primary check

i.

Turn the power switch off. Wait for at least 2 seconds, then turn the power switch on (IG). The SRS warning light comes on for approximately 6 seconds and the diagnosis of the airbag system (including the seat belt pretensioners) is performed.

HINT:

If malfunctions are detected during the primary check, the SRS warning light remains on even after the primary check period of approximately 6 seconds.




b.

Constant check

i.

After the primary check, the airbag ECU assembly constantly monitors the airbag system for malfunctions.

HINT:

If malfunctions are detected during the constant check, the airbag ECU assembly functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period of approximately 6 seconds after the power switch is turned on (IG).


ii.

When the airbag system is malfunctioning:

·

The SRS warning light remains on even after the primary check period.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when turning the power switch from off to on (IG).


HINT:

The airbag ECU assembly keeps the SRS warning light on if airbags have been deployed.





SRS WARNING LIGHT CHECK


a.
C093955

Turn the power switch on (IG), and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the power switch is turned on (IG) (constant check).

HINT:

When any of the following symptoms occur, refer to Problem Symptoms Table (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE).

·

The SRS warning light comes on occasionally after the primary check period.

·

The SRS warning light comes on, but a DTC is not output.

·

The power switch is turned from off to on (IG), but the SRS warning light does not come on.





FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (WITH AIRBAG CUT OFF SWITCH)


a.

Initial check

i.

Turn the power switch on (IG).


ii.

The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then goes off for approximately 2 seconds.

C123768E99
0.229,0.417 1.156,0.75 0.927,0.333 10 Power Switch 0.229,1.302 1.365,1.885 1.135,0.583 10 Passenger Airbag ON/OFF Indicator ("ON") 0.229,2.313 1.365,2.927 1.135,0.615 10 Passenger Airbag ON/OFF Indicator ("OFF") 1.604,0.646 1.906,0.802 0.302,0.156 10 OFF 1.583,0.229 2.198,0.531 0.615,0.302 10 On (IG) 1.594,1.708 1.896,1.854 0.302,0.146 10 OFF 1.594,1.281 1.833,1.448 0.24,0.167 10 ON 1.604,2.688 1.906,2.927 0.302,0.24 10 OFF 1.604,2.281 1.844,2.531 0.24,0.25 10 ON 3.094,0.885 3.5,1.042 0.406,0.156 10 4 sec. 3.094,1.844 3.542,2.01 0.448,0.167 10 4 sec. 4.188,0.885 4.594,1.042 0.406,0.156 10 2 sec. 4.188,1.844 4.625,2 0.438,0.156 10 2 sec. 4.594,3.042 6.75,3.417 2.156,0.375 10 ON/OFF condition depends on the front passenger detection results.


iii.

Approximately 6 seconds after the power switch is turned on (IG), the passenger airbag ON/OFF indicator will be ON/OFF depending on the conditions listed below.

Indicator Operation
Airbag Cut OFF Switch Cylinder Sub-assembly Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
ON ON OFF OFF
OFF OFF ON OFF
Switch failure OFF ON ON

HINT:

If the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cut off switch cylinder sub-assembly status, and the SRS warning light is off, no DTC will be output. Therefore, perform troubleshooting for Trouble in Passenger Airbag ON/OFF Indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>Trouble in Passenger Airbag ON/OFF Indicator).





PASSENGER AIRBAG ON/OFF INDICATOR CHECK (WITH AIRBAG CUT OFF SWITCH)


a.
C444146

Turn the power switch on (IG).


b.

Check that the passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then goes off for approximately 2 seconds.

HINT:

Refer to the indicator operation table in the preceding step regarding the passenger airbag ON/ OFF indicator when the power switch is turned on (IG) and approximately 6 seconds elapse.




FUNCTION OF SRS CONNECTORS


a.

The SRS connectors are located as shown in the illustration.

C261683E09
5.073,1.031 6.625,1.531 1.552,0.5 10 false Airbag ECU Assembly 4.76,1.531 5.083,1.865 0.323,0.333 10 false 1 4.771,1.823 5.094,2.156 0.323,0.333 10 false 2 5.719,1.531 6.042,1.865 0.323,0.333 10 false 3 6.604,1.531 6.927,1.865 0.323,0.333 10 false 3 5.719,1.823 6.042,2.156 0.323,0.333 10 false 4 6.594,1.823 6.917,2.156 0.323,0.333 10 false 4 5.708,1.677 6.031,2.01 0.323,0.333 10 false A 0.5,1.948 2.583,2.417 2.083,0.469 10 false Combination Meter Sub-assembly (SRS Warning Light) 0.417,3.521 2.958,4.01 2.542,0.49 10 false Air Conditioning Control Assembly (Passenger Airbag ON/OFF Indicator)* 0.865,4.521 2.323,4.896 1.458,0.375 10 false Front Airbag Sensor LH 0.219,2.917 3.115,3.333 2.896,0.417 10 false Airbag Cut Off Switch Cylinder Sub-assembly* 0.854,5.302 2.354,5.781 1.5,0.479 10 false Front Airbag Sensor RH 0.146,5.854 3.052,6.385 2.906,0.531 10 false Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib) 0.188,6.635 3.021,7.229 2.833,0.594 10 false Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 0.656,7.417 2.094,8.01 1.438,0.594 10 false Horn Button Assembly (Driver Side Squib) 3.177,7.438 4.656,7.885 1.479,0.448 10 false Spiral Cable with Sensor Sub-assembly 4.646,7.26 4.948,7.74 0.302,0.479 10 false 5 4.885,7.74 5.188,8.219 0.302,0.479 10 false 6 2.656,7.281 2.958,7.76 0.302,0.479 10 false 7 2.906,7.719 3.208,8.198 0.302,0.479 10 false 8 3.844,6.76 4.146,7.24 0.302,0.479 10 false 9 4.208,6.75 4.51,7.229 0.302,0.479 10 false 10 3.406,6.948 3.708,7.427 0.302,0.479 10 false 12 3.135,6.479 3.438,6.958 0.302,0.479 10 false 11 3.396,6.188 3.698,6.667 0.302,0.479 10 false 14 3.135,5.719 3.438,6.198 0.302,0.479 10 false 13 3.792,5.188 4.094,5.667 0.302,0.479 10 false 15 4.198,5.188 4.5,5.667 0.302,0.479 10 false 16 3.146,4.938 3.448,5.417 0.302,0.479 10 false 17 3.396,5.396 3.698,5.875 0.302,0.479 10 false 18 3.802,4.438 4.104,4.917 0.302,0.479 10 false 15 4.198,4.438 4.5,4.917 0.302,0.479 10 false 16 3.156,4.156 3.458,4.635 0.302,0.479 10 false 17 3.396,4.635 3.698,5.115 0.302,0.479 10 false 18 3.146,3.354 3.448,3.833 0.302,0.479 10 false 19 3.396,3.844 3.698,4.323 0.302,0.479 10 false 20 3.156,2.573 3.458,3.052 0.302,0.479 10 false 21 3.406,3.031 3.708,3.51 0.302,0.479 10 false 22 0.146,8.521 2.271,8.813 2.125,0.292 10 false *: w/ Airbag Cut Off Switch

C261684E01
4.993,1.05 6.408,1.196 1.415,0.146 10 Airbag ECU Assembly 2.684,4.486 2.858,4.632 0.173,0.145 10 29 2.934,4.934 3.107,5.080 0.173,0.145 10 30 2.684,3.72 2.858,3.866 0.173,0.145 10 27 2.934,4.183 3.107,4.328 0.173,0.145 10 28 2.684,5.236 2.858,5.382 0.173,0.145 10 31 2.934,5.717 3.107,5.863 0.173,0.145 10 32 6.559,1.838 6.663,1.979 0.104,0.141 10 4 6.559,1.529 6.663,1.674 0.104,0.145 10 3 4.696,1.838 4.799,1.979 0.104,0.141 10 2 4.696,1.529 4.799,1.674 0.104,0.145 10 1 5.648,1.838 5.752,1.979 0.104,0.141 10 4 5.648,1.529 5.752,1.674 0.104,0.145 10 3 2.684,2.146 2.858,2.291 0.173,0.145 10 23 2.934,2.673 3.114,2.819 0.180,0.145 10 24 2.684,2.907 2.858,3.052 0.173,0.145 10 25 2.934,3.392 3.110,3.538 0.176,0.145 10 26 5.644,1.695 5.755,1.836 0.111,0.141 10 A 0.271,4.609 2.464,4.916 2.193,0.307 10 Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH) 0.286,5.369 2.477,5.685 2.191,0.316 10 Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 0.162,3.278 2.663,3.420 2.501,0.143 10 Side No. 2 Airbag Sensor Assembly LH 0.413,3.849 2.398,4.160 1.986,0.311 10 Front Seat Airbag Assembly LH (Side Squib LH) 0.345,2.518 2.483,2.667 2.137,0.149 10 Side Airbag Sensor Assembly LH

C261685E02
0.896,0.99 2.302,1.135 1.406,0.146 10 false Airbag ECU Assembly 3.521,4.135 3.698,4.281 0.177,0.146 10 false 28 3.792,3.635 3.969,3.781 0.177,0.146 10 false 27 3.792,4.479 3.969,4.625 0.177,0.146 10 false 29 3.521,5 3.698,5.146 0.177,0.146 10 false 30 3.792,5.323 3.969,5.469 0.177,0.146 10 false 31 3.521,5.823 3.698,5.969 0.177,0.146 10 false 32 2.51,1.74 2.615,1.885 0.104,0.146 10 false 4 2.51,1.448 2.615,1.594 0.104,0.146 10 false 3 0.635,1.74 0.74,1.885 0.104,0.146 10 false 2 0.635,1.448 0.74,1.594 0.104,0.146 10 false 1 1.615,1.74 1.719,1.885 0.104,0.146 10 false 4 1.615,1.448 1.719,1.594 0.104,0.146 10 false 3 3.792,1.906 3.969,2.052 0.177,0.146 10 false 23 3.521,2.469 3.698,2.615 0.177,0.146 10 false 24 3.792,2.771 3.969,2.917 0.177,0.146 10 false 25 3.521,3.229 3.698,3.375 0.177,0.146 10 false 26 1.615,1.604 1.729,1.75 0.115,0.146 10 false A 4.396,4.635 6.646,4.938 2.25,0.302 10 false Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH) 4.396,5.479 6.688,5.792 2.292,0.313 10 false Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 4.292,3.156 6.792,3.302 2.5,0.146 10 false Side No. 2 Airbag Sensor Assembly RH 4.49,3.771 6.531,4.083 2.042,0.313 10 false Front Seat Airbag Assembly RH (Side Squib RH) 4.5,2.313 6.635,2.458 2.135,0.146 10 false Side Airbag Sensor Assembly RH

Connector Type Application
Terminal Twin-lock Mechanism Connectors 2, 4, 6, 9, 10, 15, 16, 20, 22
Half Connection Prevention Mechanism Connectors 6, 10, 15
Activation Prevention Mechanism Connectors 2, 4, 5, 7, 9, 11, 13, 27, 29, 31
Connector Lock Mechanism (1) Connectors 8, 12, 14, 30, 32
Connector Position Assurance Mechanism Connectors 18, 24, 26, 28
Connector Lock Mechanism (2) Connector A
Improper Connection Prevention Lock Mechanism Connector A


b.

Terminal twin-lock mechanism

C190972E45
2.823,0.656 2.479,0.104 2.479,0.104 2.031,0.104 false 5.823,0.635 5.677,0.104 5.677,0.104 5.552,0.104 false 0.646,0.021 2,0.198 1.354,0.177 10 false Lance (Primary Lock) 1.229,1.469 2.167,1.646 0.938,0.177 10 false Primary Lock 3.948,0.021 5.625,0.198 1.677,0.177 10 false Spacer (Secondary Lock) 4.896,1.448 5.948,1.625 1.052,0.177 10 false Secondary Lock

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E64
1.542,1.417 1.438,1.083 1.438,1.083 1.292,1.083 false 1.833,1.365 1.698,0.833 1.698,0.833 1.521,0.833 false 2.375,1.313 2.146,0.531 2.146,0.531 1.938,0.531 false 2.99,1.188 3.177,0.583 3.177,0.583 3.385,0.583 false 3.26,1.313 3.438,0.875 3.438,0.875 3.615,0.875 false 6.104,1.135 5.896,0.74 5.896,0.74 5.698,0.74 false 1.125,0.458 2,0.646 0.875,0.188 10 false Locking Arm 0.979,0.729 1.521,0.896 0.542,0.167 10 false Stopper 0.469,1 1.302,1.177 0.833,0.177 10 false Locking Part 3.448,0.5 3.885,0.688 0.438,0.188 10 false Slider 3.667,0.802 4.135,0.99 0.469,0.188 10 false Spring 5.177,0.646 5.76,0.833 0.583,0.188 10 false Stopper 4.646,1.948 5.979,2.135 1.333,0.188 10 false Rebounded by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected due to the spring force so that no continuity exists.



d.

Activation prevention mechanism

C238382E10
1.583,1.063 1.198,0.917 false 5.26,1.521 5.26,2.042 false 1.844,1.667 1.844,2.083 false 1.656,1.448 1.198,1.448 false 2.646,1.646 2.969,1.646 false 2.354,1.385 3,0.969 3,0.969 2.552,1.458 false 1.771,0.375 2.542,0.542 0.771,0.167 10 false When open 0.313,0.833 1.219,1.021 0.906,0.188 10 false Male Housing 3.042,0.885 4.125,1.042 1.083,0.156 10 false Female Terminal 0.302,1.375 1.219,1.542 0.917,0.167 10 false Male Terminal 3.01,1.573 4.073,1.76 1.063,0.188 10 false Female Housing 1.26,2.104 2.531,2.354 1.271,0.25 10 false Short Spring Plate 5.448,0.375 6.365,0.542 0.917,0.167 10 false When shorted 4.375,2.063 6.167,2.385 1.792,0.323 10 false Short spring plate contacting the male terminal

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive and negative terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E74
2.521,0.354 2.021,0.229 false 2.625,0.76 2.271,0.885 false 2.458,1.25 2.26,1.333 false 4.927,0.906 5.229,0.719 false 0.531,0.125 2.01,0.302 1.479,0.177 10 false Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 false Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 false Groove 5.271,0.625 6.979,0.958 1.708,0.333 10 false Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector lock button engages the locking button claw to the groove on the other side connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E56
0.833,1.146 0.833,0.208 0.833,0.208 1.01,0.208 false 0.938,1.24 1.042,0.49 1.042,0.49 1.208,0.49 false 0.5,1.833 0.75,2.292 0.75,2.292 0.948,2.292 false 5.646,1.135 5.646,0.792 5.646,0.792 5.458,0.792 false 1.063,0.125 2.271,0.292 1.208,0.167 10 false Female Connector 1.26,0.406 2.094,0.573 0.833,0.167 10 false Locking Part 1,2.219 2.063,2.396 1.063,0.177 10 false Male Connector 2.958,0.302 4.542,0.458 1.583,0.156 10 false Primary Lock Completed 5.073,0.302 6.844,0.458 1.771,0.156 10 false Secondary Lock Completed 4.896,0.698 5.521,0.875 0.625,0.177 10 false Retainer

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side and secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, they are completely engaged.



g.

Connector lock mechanism (2)

C327538E01
0.833,2.073 0.979,2.073 0.979,2.073 1.135,1.521 false 3.938,3.156 4.083,3.156 4.083,3.156 4.208,2.823 false 4.625,3.448 4.771,3.448 4.771,3.448 5.51,3.333 false 5.479,2.604 5.625,2.604 5.625,2.604 5.771,2.833 false 6.021,2.333 5.906,2.333 5.906,2.333 5.896,2.719 false 4.781,1.792 4.667,1.792 4.667,1.792 4.396,1.51 false 2.531,3.583 2.417,3.583 2.417,3.583 1.854,3.177 false 0.417,1.979 1.188,2.177 0.771,0.198 10 false Lance 3.385,3.063 4.156,3.26 0.771,0.198 10 false Retainer 2.615,3.469 3.385,3.667 0.771,0.198 10 false Retainer 4.063,3.354 4.833,3.552 0.771,0.198 10 false Retainer 5.031,2.531 5.802,2.729 0.771,0.198 10 false Holder 4.854,1.708 5.625,1.906 0.771,0.198 10 false Holder 6.073,2.25 6.844,2.448 0.771,0.198 10 false Claw

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer to the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C204952E03
3.957,0.077 4.585,0.215 0.628,0.139 10 Top View 0.247,2.353 0.941,2.492 0.694,0.139 10 Unlock Rib 3.879,1.79 4.619,2.101 0.739,0.311 10 Temporary Hold Lock 4.234,2.952 4.612,3.094 0.378,0.142 10 Lever 5.699,0.146 6.393,0.291 0.694,0.145 10 Unlock Rib 1.335,0.427 1.461,0.567 0.126,0.140 10 A 5.313,0.793 5.313,0.219 5.313,0.219 5.677,0.219 false 5.293,1.167 5.293,1.874 5.293,1.874 4.599,1.874 false 4.983,3.025 4.599,3.025 false 1.104,1.487 1.103,2.409 1.103,2.409 0.944,2.409 false 0.993,1.168 0.993,0.497 0.993,0.497 1.303,0.497 false 5.965,0.566 6.122,0.711 0.157,0.145 10 A 6.007,0.719 6.007,1.033 6.007,1.033 5.523,1.033 false

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag ECU assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around the axis A.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector (on the airbag ECU assembly side) of the airbag system squib circuit to prevent accidental airbag activation.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag activation.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.

·

To prevent the terminal and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C247058E03
0.167,0.087 3.542,0.298 3.375,0.212 10 Wire harness connector (to Airbag ECU Assembly): 1.547,1.873 2.572,2.043 1.024,0.170 10 Before Release 4.578,1.873 5.439,2.034 0.861,0.160 10 After Release 3.211,2.151 3.658,2.374 0.447,0.223 10 Paper 6.165,2.139 6.569,2.303 0.404,0.164 10 Paper 1.424,3.291 2.217,3.452 0.793,0.160 10 Short Spring 4.352,3.341 5.156,3.504 0.804,0.163 10 Short Spring 3.075,4.028 4.064,4.183 0.988,0.155 10 Before Release 2.46,6.179 3.484,6.358 1.024,0.179 10 Before Release 5.335,4.028 6.202,4.193 0.867,0.165 10 After Release 5.259,6.179 6.161,6.366 0.902,0.187 10 After Release 3.899,6.43 4.315,6.594 0.416,0.164 10 Paper 4.402,4.247 4.807,4.400 0.405,0.153 10 Paper 6.587,4.258 7.043,4.463 0.456,0.204 10 Paper 3.406,7.269 4.203,7.432 0.797,0.163 10 Short Spring 2.805,2.786 3.183,2.264 3.183,2.264 2.778,2.478 false 2.212,2.889 1.818,3.29 1.818,3.29 2.208,2.576 false 5.193,2.577 4.751,3.313 4.751,3.313 5.202,2.89 false 5.655,2.781 6.125,2.231 6.125,2.231 5.673,2.478 false 6.433,4.712 6.508,4.349 6.508,4.349 6.573,4.349 false 4.188,4.716 4.314,4.328 4.314,4.328 4.379,4.328 false 5.244,5.443 6.052,5.648 0.808,0.205 10 Short Spring 5.641,4.669 5.641,5.424 false 3.059,5.425 3.854,5.630 0.795,0.205 10 Short Spring 3.445,4.667 3.445,5.418 false 3.878,6.528 3.787,6.528 3.787,6.528 3.668,6.872 false 3.125,7.008 3.31,7.367 3.31,7.367 3.387,7.367 false 6.614,6.43 7.030,6.594 0.416,0.164 10 Paper 6.122,7.269 6.918,7.432 0.797,0.163 10 Short Spring 6.594,6.528 6.503,6.528 6.503,6.528 6.384,6.872 false 5.841,7.008 6.026,7.367 6.026,7.367 6.103,7.367 false 0.167,3.77 3.384,3.912 3.217,0.142 10 Spiral Cable with Sensor Sub-assembly Connector: 0.167,5.863 2.668,6.054 2.501,0.191 10 No. 3 Instrument Panel Wire Connector: 1.069,0.474 2.475,0.727 1.406,0.253 10 Instrument Panel Wire 3.597,0.474 4.266,0.648 0.670,0.174 10 Floor Wire 5.014,0.474 6.076,0.648 1.062,0.174 10 No. 2 Floor Wire 0.543,7.465 1.650,7.628 1.108,0.163 10 : Short Spring