Home › Engine / Hybrid System › 2ZR-FXE (INTAKE / EXHAUST) › EXHAUST PIPE › from 2020.08
RM2070E _51 Engine / Hybrid System _061910 2ZR-FXE INTAKE / EXHAUST _0301619 EXHAUST PIPE A

2ZR-FXE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum 41.5 mm (1.64 in.)

HINT:

If the free length is less than the minimum, replace the compression spring.



b.

Fully insert a new gasket to the exhaust manifold.


c.
A181728E17
1.074,0.399 1.283,0.621 0.209,0.223 10 *1 0.736,2.568 0.956,2.724 0.221,0.156 10 *2 2.726,1.902 2.949,2.042 0.223,0.140 10 *3 1.359,0.466 1.509,0.466 1.509,0.466 1.834,1.116 false 2.042,2.337 1.19,2.651 1.19,2.651 0.986,2.651 false 2.522,1.415 2.831,1.596 2.831,1.596 2.831,1.831 false

Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold.

Text in Illustration
*1 Exhaust Manifold
*2 Gasket
*3 Wooden Block

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 57533B 3.INSTALL FRONT CENTER FLOOR BRACE

a.

Install the front center floor brace with the 4 bolts.

Torque:
51 N*m (520 kgf*cm, 38 ft.*lbf)


Hide 17430 5.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum 38.5 mm (1.52 in.)

HINT:

If the free length is less than the minimum, replace the compression spring.



b.

Fully insert a new gasket to the front exhaust pipe assembly.


c.
A181728E17
1.074,0.399 1.283,0.621 0.209,0.223 10 *1 0.736,2.568 0.956,2.724 0.221,0.156 10 *2 2.726,1.902 2.949,2.042 0.223,0.140 10 *3 1.359,0.466 1.509,0.466 1.509,0.466 1.834,1.116 false 2.042,2.337 1.19,2.651 1.19,2.651 0.986,2.651 false 2.522,1.415 2.831,1.596 2.831,1.596 2.831,1.831 false

Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the front exhaust pipe assembly.

Text in Illustration
*1 Front Exhaust Pipe Assembly
*2 Gasket
*3 Wooden Block

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.


e.

Install the tail exhaust pipe assembly with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 6.INSPECT FOR EXHAUST GAS LEAK