Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2020.08
RM2070E _59 Vehicle Exterior _061952 WIPER / WASHER _0301891 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Speed Signal Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a vehicle speed signal from the combination meter to control the automatic windshield wiper system.

A voltage of 12 V or 5 V is output from the combination meter assembly and then input to the skid control ECU.

A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly.

Each ECU controls the respective system based on the pulse signal.

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

WIRING DIAGRAM

E436060E01
0.688,1.417 1.146,1.615 0.458,0.198 10 false A58 0.677,1.594 2.083,1.99 1.406,0.396 10 false Skid Control ECU 0.063,2.802 0.521,3 0.458,0.198 10 false L197 0.042,2.979 3.021,3.438 2.979,0.458 10 false Certification ECU (Smart Key ECU Assembly) 1.406,0.521 1.865,0.719 0.458,0.198 10 false SP1 5.271,0.531 5.729,0.729 0.458,0.198 10 false 16 1.406,2.417 1.865,2.615 0.458,0.198 10 false SPD 1.802,2.417 2.26,2.615 0.458,0.198 10 false 27 5.563,0.646 6.021,0.844 0.458,0.198 10 false S1 5.281,0.927 5.74,1.125 0.458,0.198 10 false 15 5.552,1.052 6.01,1.25 0.458,0.198 10 false +S 3.531,1.813 3.99,2.01 0.458,0.198 10 false 32 2.854,2.438 3.313,2.635 0.458,0.198 10 false 22 3.927,2.438 4.385,2.635 0.458,0.198 10 false 31 5.292,2.427 5.75,2.625 0.458,0.198 10 false 16 4.958,4.292 5.417,4.49 0.458,0.198 10 false L146 4.99,2.99 7.104,3.583 2.115,0.594 10 false Headlight Leveling ECU Assembly 5.552,2.427 6.01,2.625 0.458,0.198 10 false SPDR 3.917,3.896 4.375,4.094 0.458,0.198 10 false 12 3.052,4.448 4.333,4.854 1.281,0.406 10 false Junction Connector 2.698,4.458 3.156,4.656 0.458,0.198 10 false L70 4.969,4.469 7.156,4.885 2.188,0.417 10 false Windshield Wiper Relay Assembly 1.802,0.521 2.26,0.719 0.458,0.198 10 false 11 5.552,3.896 6.01,4.094 0.458,0.198 10 false SPD 5.271,3.885 5.729,4.083 0.458,0.198 10 false 24 5,2.823 5.458,3.021 0.458,0.198 10 false A48 5.01,1.406 5.375,1.635 0.365,0.229 10 false L27 5,1.573 7.094,1.958 2.094,0.385 10 false Combination Meter Sub-assembly

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (SPEED SENSOR SIGNAL)
a.
U190824E02
1.271,1.229 1.073,0.698 true 1.135,3.896 1.385,3.896 false 1.073,3.708 1.073,4.031 false 1.438,3.708 1.438,4.031 false 0.135,0.115 0.292,0.271 0.156,0.156 10 false *a 0.938,0.51 1.125,0.667 0.188,0.156 10 false +S 2.781,3.635 3.104,3.792 0.323,0.156 10 false GND 1.146,3.927 1.354,4.083 0.208,0.156 10 false (A) 1.615,0.469 1.917,0.625 0.302,0.156 10 false L27

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER)

NG

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER)
a.

Disconnect the L146 windshield wiper relay assembly connector and L27 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L146-24 (SPD) - L27-15 (+S) Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR