The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter sub-assembly. The combination meter sub-assembly detects rear seat belt state. The rear seat belt warning light on the combination meter sub-assembly illuminates or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.
The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Door Courtesy SW | Rear door courtesy light switch signal/ON or OFF | ON: Rear door RH or LH open
OFF: Rear door RH and LH closed |
- |
| RL Door Courtesy SW | Rear door courtesy light switch signal/ON or OFF | ON: Rear door LH or RH open
OFF: Rear door LH and RH closed |
- |
ON or OFF appears on the tester screen according to the rear door condition.
OK
NG
| *a | Rear Seat Belt Warning Light (Combination Meter Sub-assembly) |
| *b | Rear No. 1 Seat LH |
| *c | Rear No. 1 Seat Center |
| *d | Rear No. 1 Seat RH |
| *e | Rear No. 2 Seat LH |
| *f | Rear No. 2 Seat RH |
Check the rear seat belt warning function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION).
| Result | Proceed to |
|---|---|
| The rear seat belt warning lights operation is normal | A |
| The rear seat belt warning lights (all seat) operation is not normal | B |
| The rear seat belt warning lights (any seat) operation is not normal | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Replace the combination meter sub-assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).
NEXT
Check the rear seat belt warning function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION).
The rear seat belt warning function operates normally.
OK
NG
| *a | Rear Seat Belt Warning Light (Combination Meter Sub-assembly) |
| *b | Rear No. 1 Seat LH |
| *c | Rear No. 1 Seat Center |
| *d | Rear No. 1 Seat RH |
| *e | Rear No. 2 Seat LH |
| *f | Rear No. 2 Seat RH |
Check the rear seat belt warning function (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION).
| Result | Proceed to |
|---|---|
| The rear seat belt warning light (rear No. 1 seat LH) operation is not normal | A |
| The rear seat belt warning light (rear No. 1 seat center) operation is not normal | B |
| The rear seat belt warning light (rear No. 1 seat RH) operation is not normal | C |
| The rear seat belt warning light (rear No. 2 seat LH) operation is not normal | D |
| The rear seat belt warning light (rear No. 2 seat RH) operation is not normal | E |
A
B
C
D
E
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| 2nd-Row Seatbelt Buckle (L) | Rear No. 1 seat belt LH buckle switch signal/ON or OFF | ON: Rear No. 1 seat belt LH not fastened
OFF: Rear No. 1 seat belt LH fastened |
- |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the rear seat belt condition | A |
| ON or OFF appears on the tester screen according to the rear seat belt condition | B |
A
B
Disconnect the L27 combination meter sub-assembly connector.
Disconnect the R35 rear seat 3 point type belt assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-38 (RLSB) - R35-1 (LBR+) | Always | Below 1 Ω |
| L27-38 (RLSB) - Body ground | Always | 10 kΩ or higher |
| R35-2 (LBR-) - Body ground | Always | Below 1 Ω |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| 2nd-Row Seatbelt Buckle (C) | Rear No. 1 seat belt center buckle switch signal/ON or OFF | ON: Rear No. 1 seat belt center not fastened
OFF: Rear No. 1 seat belt center fastened |
- |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the rear seat belt condition | A |
| ON or OFF appears on the tester screen according to the rear seat belt condition | B |
A
B
Disconnect the L27 combination meter sub-assembly connector.
Disconnect the R36 rear seat inner belt assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-37 (RCSB) - R36-1 (CBR+) | Always | Below 1 Ω |
| L27-37 (RCSB) - Body ground | Always | 10 kΩ or higher |
| R36-2 (CBR-) - Body ground | Always | Below 1 Ω |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| 2nd-Row Seatbelt Buckle (R) | Rear No. 1 seat belt RH buckle switch signal/ON or OFF | ON: Rear No. 1 seat belt RH not fastened
OFF: Rear No. 1 seat belt RH fastened |
- |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the rear seat belt condition | A |
| ON or OFF appears on the tester screen according to the rear seat belt condition | B |
A
B
Disconnect the L27 combination meter sub-assembly connector.
Disconnect the S28 rear seat 3 point type belt assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-36 (RRSB) - S28-1 (RBR+) | Always | Below 1 Ω |
| L27-36 (RRSB) - Body ground | Always | 10 kΩ or higher |
| S28-2 (RBR-) - Body ground | Always | Below 1 Ω |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| 3rd-Row Seatbelt Buckle (L) | Rear No. 2 seat belt LH buckle switch signal/ON or OFF | ON: Rear No. 2 seat belt LH not fastened
OFF: Rear No. 2 seat belt LH fastened |
- |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the rear seat belt condition | A |
| ON or OFF appears on the tester screen according to the rear seat belt condition | B |
A
B
Disconnect the L27 combination meter sub-assembly connector.
Disconnect the S29 rear No. 2 seat inner belt assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-40 (RLBT) - S29-3 (+) | Always | Below 1 Ω |
| L27-40 (RLBT) - Body ground | Always | 10 kΩ or higher |
| S29-2 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| 3rd-Row Seatbelt Buckle (R) | Rear No. 2 seat belt RH buckle switch signal/ON or OFF | ON: Rear No. 2 seat belt RH not fastened
OFF: Rear No. 2 seat belt RH fastened |
- |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the rear seat belt condition | A |
| ON or OFF appears on the tester screen according to the rear seat belt condition | B |
A
B
Disconnect the L27 combination meter sub-assembly connector.
Disconnect the S29 rear No. 2 seat inner belt assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-39 (RRBT) - S29-1 (+) | Always | Below 1 Ω |
| L27-39 (RRBT) - Body ground | Always | 10 kΩ or higher |
| S29-4 (E) - Body ground | Always | Below 1 Ω |
OK
NG