Home › Brake › BRAKE (REAR) › REAR BRAKE FLEXIBLE HOSE

REAR BRAKE FLEXIBLE HOSE > INSTALLATION

for Preparation Click here


NOTICE:
  1. Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the flexible hoses.
  2. If the hoses are to be reused, connect them after checking the identification marks placed when each hose was disconnected.



1. INSTALL REAR FLEXIBLE HOSE
  1. Install the rear flexible hose with 2 new clips.

    NOTICE:
    Install the clip as far as it will go.

  1. Using a union nut wrench, connect the 2 brake lines to the rear flexible hose while holding the rear flexible hose with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not kink or damage the brake line.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake line.
    3. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    4. This torque value is effective when the union nut wrench is parallel to the torque wrench.
    5. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



2. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL



3. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for RH Side)
  1. Install the No. 1 fuel tank protector sub-assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Install the clip.



4. INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR (for RH Side)


    C247550E01
  1. Install the front No. 4 floor heat insulator with the 2 nuts.

    Torque:
    Nut A:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut B:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



5. BLEED BRAKE LINE


    C250009
  1. Disengage the 4 claws and 6 guides, and separate the center No. 1 cowl top ventilator louver.



  1. Bleed brake line.



      C250010
    1. Remove the brake master cylinder reservoir filler cap assembly.

    2. Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    3. Connect the Techstream to the DLC3 and turn the ignition switch to ON (IG).

    4. Turn the Techstream on and enter the following menus: Chassis / ABS/VSC/TRAC / Air Bleeding.

    5. Select "Usual air bleeding" on the Techstream display, and bleed air from the brake fluid following the instructions on the Techstream.

    6. After air bleeding, tighten each bleeder plug.

      Torque:
      front bleeder plug:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      rear bleeder plug:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    7. Clear the DTCs (Click here).

    8. Turn the Techstream off and turn the ignition switch off.

    9. Install the brake master cylinder reservoir filler cap.

  1. Inspect for brake fluid leaks.

  1. Engage the 4 claws and 6 guides to install the center No. 1 cowl top ventilator louver.



6. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }