Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    B296191
  1. Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

    NOTICE:
    Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



2. INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
  1. Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



  1. Install the 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.


    B298731E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Ceramic Notch
    -
    -
    *a
    Windshield Glass Edge Side
    -
    -

    Standard Dimension:

    Area
    Dimension
    a
    7.2 to 8.2 mm (0.283 to 0.323 in.)

    NOTICE:
    Only 2-piece type windshield glass stoppers are provided as supply parts. Use the 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



3. INSTALL WINDOW GLASS ADHESIVE DAM


  1. Using a brush or sponge, coat the application area of a new window glass adhesive dam with primer G.


    B298739E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Primer G
    *2
    Ceramic Notch for Dam Cut Alignment
    *a
    Dam Cut Area
    *b
    Ceramic Line

    Standard Dimension:

    Area
    Dimension
    a
    5.2 mm (0.205 in.)
    b
    7.0 mm (0.276 in.)
    c
    7.0 mm (0.276 in.)
    d
    5.2 mm (0.205 in.)
    e
    34.8 mm (1.37 in.)

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



  1. Install the window glass adhesive dam onto the windshield glass as shown in the illustration.


    B298741E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Ceramic Notch for Dam Cut Alignment
    -
    -
    *a
    Dam Cut Area
    *b
    Ceramic Line

    Standard Dimension:

    Area
    Dimension
    a
    7.0 mm (0.276 in.)
    b
    7.0 mm (0.276 in.)
    c
    35.0 mm (1.38 in.)



4. INSTALL WINDSHIELD GLASS SUB-ASSEMBLY


    B296183E01
  1. Position the windshield glass sub-assembly.
    Text in Illustration 
    *1
    Matchmark

    1. Using suction cups, place the windshield glass sub-assembly in the correct position.

    2. Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.

    3. Align the matchmarks on the windshield glass sub-assembly and vehicle body.

      NOTICE:
      Check that the windshield glass stoppers are attached to the vehicle body correctly.

    4. Remove the windshield glass sub-assembly.



  1. Using a brush, coat the installation surface on the vehicle body with primer M.


    B308012E01


    Text in Illustration 
    *1
    Brush
    *2
    Primer M
    *3
    Adhesive
    -
    -
    *a
    CORRECT
    *b
    INCORRECT
    *c
    Edge of Curved Surface
    -
    -

    NOTICE:
    1. Do not coat the adhesive with primer M.
    2. Do not apply too much primer M.
    3. Allow the primer M to dry for 3 minutes or more.
    4. Throw away any leftover primer M.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



  1. Using a brush or sponge, coat the application area of adhesive with primer G.


    B300465E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Primer G
    *2
    Ceramic Notch

    Standard Dimension:

    Area
    Dimension
    a
    7.0 mm (0.276 in.) or more
    b
    7.0 mm (0.276 in.) or more
    c
    7.0 mm (0.276 in.) or more
    d
    19.0 mm (0.748 in.) or more

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    1. Apply primer G onto the ceramic notches.
    2. If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E05
    1. Cut off the tip of the cartridge nozzle as shown in the illustration.
      Text in Illustration 
      *1
      Nozzle

      Standard Dimension:
      Area
      Dimension
      a
      8.0 mm (0.315 in.) or more
      b
      12.0 mm (0.472 in.) or more

      HINT:
      After cutting off the tip, use all adhesive within the time described in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the windshield glass sub-assembly as shown in the illustration.


      B300466E01


      Text in Illustration 
      *A
      Back Side
      -
      -
      *1
      Adhesive
      *2
      Ceramic Notch

      Standard Dimension:

      Area
      Dimension
      a
      8.0 mm (0.315 in.) or more
      b
      8.0 mm (0.315 in.) or more
      c
      8.0 mm (0.315 in.) or more
      d
      19.0 mm (0.748 in.) or more
      e
      8.0 mm (0.315 in.) or more
      f
      8.0 mm (0.315 in.) or more

      HINT:
      Apply adhesive onto the ceramic notches.



    B296183E01
  1. Install the windshield glass sub-assembly.
    Text in Illustration 
    *1
    Matchmark

    1. Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

      NOTICE:
      1. Check that the windshield glass stoppers are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and windshield glass sub-assembly.

    2. Lightly press the front surface of the windshield glass sub-assembly to ensure that the windshield glass is securely fit to the vehicle body.

      HINT:
      Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.

    3. Using a scraper, remove any excess or protruding adhesive.

    4. Hold the windshield glass using protective tape until the applied adhesive becomes hard.

      NOTICE:
      Do not drive the vehicle for the time described in the table below.

      Minimum Time:
      Temperature
      Minimum Time prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



5. INSTALL WINDSHIELD OUTSIDE MOULDING

NOTICE:
After the installation of the window glass, install the moulding before the adhesive hardens.

  1. Using a brush or sponge, coat the application area of a new windshield outside moulding with primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



    B300468
  1. Apply primer G to the shaded area of the upper side of the windshield outside moulding as shown in the illustration.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



    B300428E01
  1. Install the windshield outside moulding onto the windshield glass.
    Text in Illustration 
    *1
    Window Glass
    *2
    Windshield Outside Moulding
    *3
    Body



6. INSPECT FOR LEAK AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.



7. INSTALL ROOF HEADLINING ASSEMBLY
(Click here)


8. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 8 guides as shown in the illustration.


    E237534



  1. Engage the 3 guides and 5 claws to install the cowl top ventilator louver sub-assembly as shown in the illustration.


    E237532

  1. Connect the washer hose.

  1. Install the 2 clips.



9. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


  1. Clean the front fender to cowl side seal LH (if reusing the front fender to cowl side seal LH).

    1. Remove the double-sided tape from the front fender to cowl side seal LH.

    2. Wipe off any tape adhesive residue with cleaner.

    3. Coat the installation surface on the front fender to cowl side seal LH with primer N-200.

      NOTICE:
      1. Allow the primer to dry for 10 minutes or more.
      2. If 24 hours have elapsed since the primer was applied, reapply primer N-200.



    4. E246046E01
    5. Apply new double-sided tape to the front fender to cowl side seal LH as shown in the illustration.
      Text in Illustration 
      *1
      Double-sided Tape
      *a
      Edge of Curved Surface
      Item
      Dimension
      A
      0.5 mm (0.0197 in.)
      B
      5.0 mm (0.197 in.)
      C
      45.0 mm (1.77 in.)
      D
      1.0 mm (0.0394 in.)
      E
      2.0 mm (0.0787 in.)

  1. Clean the outside windshield moulding.

    1. Remove the double-sided tape from the outside windshield moulding.

    2. Wipe off any tape adhesive residue with cleaner

    3. Coat the installation surface on the outside windshield moulding with primer N-200.

      NOTICE:
      1. Allow the primer to dry for 10 minutes or more.
      2. If 24 hours have elapsed since the primer was applied, reapply primer N-200.



  1. Install the front fender to cowl side seal LH.

    1. Install the clip to the front fender to cowl side seal LH (if reusing the front fender to cowl side seal LH).

    2. Engage the 2 guides and clip to install the front fender to cowl side seal LH as shown in the illustration.



    3. E237528E01
    4. Remove the release paper from the double-sided tape on the front fender to cowl side seal LH.
      Text in Illustration 
      *1
      Double-sided Tape

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    5. Install the front fender to cowl side seal LH.



10. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure as for the LH side.



11. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E237492E01
  1. When reusing the front wiper arm and blade assembly LH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.



    E237546E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.



12. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E237492E01
  1. When reusing the front wiper arm and blade assembly RH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.



    E237547E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.

  1. Turn the ignition switch to ON (IG).

  1. Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.

  1. Lift each wiper arm twice after the wipers stop and check the wiper set position.

  1. Turn the ignition switch off.



13. INSTALL FRONT WIPER ARM HEAD CAP


    E237524
  1. Engage the 3 claws to install the front wiper arm head cap.

    HINT:
    Use the same procedure for the RH side and LH side.