Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P2118    Throttle Actuator Control Motor Current Range / Performance

for Preparation Click here


DESCRIPTION

The electronic throttle control system has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the electronic throttle control system and cuts off the current to the throttle actuator.
When the voltage becomes unstable, the electronic throttle control system itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:
The electronic throttle control system does not use a throttle cable.


A255382E13


DTC No.
DTC Detection Condition
Trouble Area
P2118
An open in the electronic throttle control system power source (+BM) circuit (1 trip detection logic).
  1. Open in electronic throttle control system power source circuit
  2. Auxiliary battery
  3. Auxiliary battery terminals
  4. ETCS fuse
  5. ECM

MONITOR DESCRIPTION

The ECM monitors the auxiliary battery supply voltage applied to the throttle actuator.
When the power supply voltage (+BM) is less than 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P2118: Electronic throttle actuator power supply line range check (low voltage)
Required Sensors/Components (Main)
Throttle actuator
Throttle valve (throttle body with motor assembly)
ETCS fuse
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.8 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not stored
None
Both of the following conditions are met
-
Command to electronic throttle actuator power
On
Auxiliary battery voltage
8 V or higher

TYPICAL MALFUNCTION THRESHOLDS


Electronic throttle actuator power supply voltage
Less than 4 V

COMPONENT OPERATING RANGE


Electronic throttle control
Normal

CONFIRMATION DRIVING PATTERN


A199315E16

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON (IG) and turn the Techstream on [A].
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine.
  8. Slowly depress the accelerator pedal, raise the engine speed to approximately 2500 rpm over approximately 5 seconds, and then idle the engine [B].

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform step [B] after charging control has completed.

  9. Check that 16 seconds or more have elapsed since the engine was started.
  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  11. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P2118.
  14. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When this DTC or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM stops the engine and the vehicle can be driver using solely the hybrid system. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (+BM VOLTAGE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Throttle / +BM Voltage.

  1. Read the value displayed on the Techstream.

    Result 
    Result
    Proceed to
    Less than 4 V
    A
    11 to 16 V
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK HARNESS AND CONNECTOR (ECM - AUXILIARY BATTERY, BODY GROUND)
  1. Disconnect the ECM connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    C10-29 (+BM) - Body ground
    Ignition switch off
    11 to 16 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C10-59 (ME01) - Body ground
    Always
    Below 1 Ω
    C10-16 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)