Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY

FRONT PASSENGER AIRBAG ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT PILLAR GARNISH RH
(Click here)


3. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B300216E02
  1. Slide the 2 sliders to release the locks, and then disconnect the 2 connectors.
    Text in Illustration 
    *a
    Slider

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



4. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY


  1. w/ Navigation System:



    1. Disconnect the connector.


      B301691



  1. Remove the bolt <A>.


    B301690E01


    Text in Illustration 
    *1
    Bolt <A>
    *2
    Screw <C>

  1. Remove the screw <C>.

  1. Using a clip remover, remove the 2 clips.



  1. Pull the upper instrument panel assembly in the direction indicated by the arrow (1) to disengage the 7 clips.


    B301692E01

  1. Pull the upper instrument panel assembly in the direction indicated by the arrow (2) to disengage the 5 guides and remove the upper instrument panel assembly.



5. REMOVE NO. 2 HEATER TO REGISTER DUCT ASSEMBLY


    B301696
  1. Remove the 3 screws <B> and No. 2 heater to register duct assembly.



6. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.



    B300219
  1. Disengage the clamp from the upper instrument panel assembly.



    B300220
  1. Disengage the clamp to separate the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.



    B300221
  1. Remove the 2 screws.



    B300222
  1. Lean the upper instrument panel assembly and disengage the 3 hooks.



    B300223
  1. Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the upper instrument panel assembly.



7. REMOVE NO. 2 INSTRUMENT PANEL WIRE


    B300224E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the vent hole connector lock.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Vent Hole Connector
    *3
    Vent Hole Connector Lock

  1. Disconnect the vent hole connector from the instrument panel passenger airbag assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



    B300226E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the 2 airbag connector locks.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Airbag Connector
    *3
    Airbag Connector Lock

  1. Disconnect the 2 airbag connectors to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.