Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT

REAR AXLE HUB BOLT > REPLACEMENT

for Preparation Click here


NOTICE:
  1. When the brake pedal is first depressed after replacing the brake shoes or pushing back the wheel brake cylinder piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.
  2. While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake shoes are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after turning the ignition switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the ignition switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C250008
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



3. REMOVE REAR WHEEL


4. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY


    C233134
  1. Release the parking brake and remove the rear brake drum sub-assembly.
    Text in Illustration 
    V100135
    Contract

    HINT:
    If the rear brake drum sub-assembly cannot be removed easily, perform the following procedure.


    1. Remove the shoe adjusting hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjust lever away from the adjuster.

    2. Using another screwdriver, contract the brake shoe by turning the adjusting bolt.



5. REMOVE REAR AXLE HUB BOLT


    C249954E01
  1. Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.
    Text in Illustration 
    *1
    Service Nut

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    NOTICE:
    Install the service nuts to prevent damage to the rear axle hub bolts.

  1. Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

    SST
    09611-12010  

    NOTICE:
    Do not damage the threads of the rear axle hub bolts.



6. INSTALL REAR AXLE HUB BOLT


    C249955E01
  1. Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
    Text in Illustration 
    *1
    Service Nut
    *2
    Washer

  1. Install a washer and service nut to the new rear axle hub bolt as shown in the illustration.

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    HINT:
    Recommended washer thickness is 5 mm (0.197 in.) or more.

  1. Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

    NOTICE:
    1. Install the service nuts to prevent damage to the rear axle hub bolts.
    2. Do not damage the threads of the rear axle hub bolts.

  1. Remove the 3 service nuts and washer from the 3 rear axle hub bolts.



7. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
  1. Install the rear brake drum sub-assembly.



8. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



9. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
  1. Connect the cable to the negative (-) auxiliary battery terminal .

  1. Connect the reservoir level switch connector.

  1. Clear the DTCs (Click here).