Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Key System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Key System) > Security Indicator Light Does not Blink

for Preparation Click here


DESCRIPTION

  1. When the engine immobiliser system is set, the security indicator light blinks continuously, but does not illuminate if the engine immobiliser system is not set.

WIRING DIAGRAM


B302043E02


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing the transponder key ECU assembly, refer to Registration (Click here).

1.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM (SECURITY INDICATOR)
  1. Check that the security indicator light illuminates when operating it with the Active Test (Click here).

    Immobiliser 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security Indicator Light
    OFF / ON
    -

    OK:
    Security indicator light can be turned on and off using the Techstream.



NG
Go to step 4
OK


3.READ VALUE USING TECHSTREAM (ENGINE IMMOBILISER SYSTEM STATUS)
  1. Turn the ignition switch off.

    HINT:
    When using the Techstream with the ignition switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds until communication between the Techstream and vehicle begins.

  1. Using the Techstream, read the Data List (Click here).

    Immobiliser 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser
    Engine immobiliser system status determined by transponder key ECU assembly / Set or Unset
    Set: Engine immobiliser set (hybrid control system start prohibited (no key in ignition key cylinder))
    Unset: Engine immobiliser unset (hybrid control system start permitted (key inserted in ignition key cylinder))
    When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.



NG
Go to step 6
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
  1. Disconnect the G46 transponder key ECU assembly connector.

  1. Disconnect the G1 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G46-8 (IND) - G1-13 (LP)
    Always
    Below 1 Ω
    G46-8 (IND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK TRANSPONDER KEY ECU ASSEMBLY


    B302044E02
  1. Reconnect the G46 transponder key ECU assembly connector.

  1. Measure the voltage and check the pulse according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G1-13 (LP) - Body ground
    Engine immobiliser system set
    Pulse generation
    G1-13 (LP) - Body ground
    Engine immobiliser system unset
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)


    B242622E15
  1. Disconnect the G46 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G46-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G46-1 (+B) - Body ground
    Ignition switch off
    11 to 14 V
    G46-2 (IG) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Transponder Key ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)