Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stored the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No.
DTC Detection Condition
Trouble Area
P0420
The oxygen storage capacity value is less than the standard value under active air fuel ratio control (1 trip detection logic).
  1. Gas leak from exhaust system
  2. Air fuel ratio sensor (sensor 1)
  3. Heated oxygen sensor (sensor 2)
  4. Exhaust manifold (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)
  5. EGR valve assembly

CATALYST LOCATION


A269949E01


Text in Illustration 
*1
Air Fuel Ratio Sensor (Sensor 1)
*2
Heated Oxygen Sensor (Sensor 2)
*3
TWC: Front Catalyst
*4
TWC: Rear Catalyst
*5
Tail Exhaust Pipe Assembly
*6
Exhaust Manifold
*7
Front Exhaust Pipe Assembly
-
-

NOTICE:
Replace the exhaust manifold (*6) and the front exhaust pipe assembly (*7) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *1 and heated oxygen sensor *2).


MONITOR STRATEGY


Related DTCs
P0420: Catalyst deterioration
Required Sensors/Components (Main)
Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related)
Intake air temperature sensor
Mass air flow meter sub-assembly
Crank position sensor
Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
Approximately 30 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not stored
P0010 (VVT oil control valve)
P0011 (VVT system - advance)
P0012 (VVT system - retard)
P0016 (VVT system - misalignment)
P0031, P0032, P101D (Air fuel ratio sensor heater)
P0037, P0038, P102D (Heated oxygen sensor heater)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0136, P0137, P0138, P0139, P0607 (Heated oxygen sensor)
P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253 (Air fuel ratio sensor)
P0171, P0172 (Fuel system)
P0301, P0302, P0303, P0304 (Misfire)
P0335 (Crankshaft position sensor)
P0340 (Camshaft position sensor)
P0351, P0352, P0353, P0354 (Igniter)
P0401 (EGR system (closed))
P219A, P219C, P219D, P219E, P219F (Air fuel ratio imbalance)
Auxiliary battery voltage
11 V or higher
Intake air temperature
-10°C (14°F) or higher
Engine coolant temperature
75°C (167°F) or higher
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or higher
Idling
Off
Engine speed
Less than 4000 rpm
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Engine load
10% or higher, and less than 70%
All of the following conditions are met
-
Mass air flow rate
1.5 gm/sec or more, and less than 40 gm/sec
Front catalyst temperature (estimated)
560°C (1040°F) or higher, and less than 770°C (1418°F)
Rear catalyst temperature (estimated)
450°C (842°F) or higher, and less than 700°C (1292°F)

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of catalyst (Normalized)
Less than 1

MONITOR RESULT

Refer to detailed information in Checking Monitor Status (Click here).

P0420: Catalyst Efficiency / O2 STORAGE B1 
Monitor ID
Test ID
Scaling
Unit
Description
$21
$AF
Multiply by 0.001
No dimension
Oxygen storage capacity of catalyst bank 1 (Normalization)

CONFIRMATION DRIVING PATTERN

HINT:
  1. It is necessary for the response of the heated oxygen sensor to be normal in order to confirm DTC P0420. Therefore, perform the confirmation driving pattern for the heated oxygen sensor monitor before performing the confirmation driving pattern for the catalyst efficiency monitor.
  2. Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283604E17

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON (IG) and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
  8. Check that Catalyst Efficiency / Current is Incomplete.
  9. Put the engine in inspection mode (maintenance mode) (Click here).
  10. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P [A].

    HINT:
    In order to keep the idle stable, turn the A/C and all other electric loads off and do not perform any shift operations.

  11. Drive the vehicle at approximately 75 km/h (47 mph) for 10 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  12. With the shift lever in B, drive the vehicle at 75 km/h (47 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  13. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2 [D].
  14. Check the Test Value for RL F/C B1S2.

    HINT:
    1. If Test Value displays a value larger than 0, perform the following procedure, as the O2 Sensor monitor is finished.
    2. If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 Sensor monitor is not finished.

  15. Turn the ignition switch off and wait for at least 30 seconds [F].
  16. Turn the ignition switch to ON (IG) and turn the Techstream on.
  17. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [G].
  18. Drive the vehicle at approximately 75 km/h (47 mph) for 10 minutes or more [H].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates.

  19. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [I].
  20. Check if any DTCs are stored.

    HINT:
    If the monitor item does not change to Complete, and no DTCs are stored, perform the following procedure.

  21. Drive the vehicle at approximately 100 km/h (62 mph) for 10 minutes or more [J].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates.

  22. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].
  23. Check if any DTCs are stored.

    HINT:
    If the monitor item does not change to Complete, and no DTCs are stored, extend the driving time.

  24. If no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A270243E01

  1. (a) Connect the Techstream to the DLC3 [A].
  2. (b) Turn the ignition switch to ON (IG) and turn the Techstream on [B].
  3. (c) Put the engine in inspection mode (maintenance mode) (Click here) [C].
  4. (d) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes [D].
  5. (e) Run the engine at an engine speed of 2500 rpm for at least 3 minutes [E].

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform step [E] after charging control has completed.

  6. (f) While running the engine at 2500 rpm for 2 seconds and 1500 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the Techstream [F].

HINT:
  1. If either of the voltage outputs of the air fuel ratio or heated oxygen sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor may be malfunctioning.
  2. If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the Techstream.
  3. If the three-way catalytic converter has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A199479E09


INSPECTION PROCEDURE

HINT:
  1. If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).
  2. Sensor 1 refers to the sensor closest to the engine assembly.
  3. Sensor 2 refers to the sensor farthest away from the engine assembly.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 is output
    A
    DTC P0420 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up.

  1. Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.

  1. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    4. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Techstream Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    (Air fuel ratio)
    12.5%
    Rich
    Below 3.1 V
    -12.5%
    Lean
    Higher than 3.4 V
    O2S B1S2
    (Heated oxygen)
    12.5%
    Rich
    Higher than 0.55 V
    -12.5%
    Lean
    Below 0.4 V


    Result 
    Status
    AFS Voltage B1S1
    Status
    O2S B1S2
    Actual air fuel ratio, air fuel ratio sensor and
    heated oxygen sensor condition
    Misfire
    Main Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-way catalytic converter
    2. Gas leak from exhaust system
    3. EGR valve assembly
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    Lean/Rich
    Lean
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leak from exhaust system
    C
    Lean/Rich
    Rich
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leak from exhaust system
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. Extremely lean actual air fuel ratio
    2. Gas leak from exhaust system
    3. EGR valve assembly
    D
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Extremely rich actual air fuel ratio
    2. Gas leak from exhaust system
    3. EGR valve assembly
    1. Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
    2. Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.
    3. Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



B
Go to step 7

C
Go to step 8

D
Go to step 10
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 14
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.

  1. Confirm that the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    (Throttle Idle Position: ON)
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    MAP
    (Data List)
    MAP value is 20 to 40 kPa(abs) [150 to 300 mmHg(abs)]
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 6
A


5.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


6.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NOTICE:
Replace the exhaust manifold (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Replace the exhaust manifold (TWC: Front catalyst) (Click here).

  1. Replace the front exhaust pipe assembly (TWC: Rear catalyst) (Click here).


NEXT

END 

7.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NEXT
Go to step 15

8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 14
OK


9.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the heated oxygen sensor (Click here).



NEXT
Go to step 15

10.CHECK FOR EXHAUST GAS LEAK
  1. Check the exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 14
OK


11.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.

  1. Confirm that the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    (Throttle Idle Position: ON)
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    MAP
    (Data List)
    MAP value is 20 to 40 kPa(abs) [150 to 300 mmHg(abs)]
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 13
A


12.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


13.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
  1. Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .



NEXT
Go to step 15

14.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
  1. Repair or replace exhaust gas leak point.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 is output
    A
    DTC is not output
    (No pending DTCs output)
    B



B
END
A


16.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NOTICE:
Replace the exhaust manifold (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Replace the exhaust manifold (TWC: Front catalyst) (Click here).

  1. Replace the front exhaust pipe assembly (TWC: Rear catalyst) (Click here).


NEXT

END