Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

DTC    B2284    Brake Signal Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

HINT:
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2284
The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection logic*) do not match.
  1. AM2 fuse
  2. STOP fuse
  3. Brake control system
  4. Power management control ECU
  5. Wire harness or connector
Connect the cable to the negative (-) auxiliary battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more.
  1. *: Only detected while a malfunction is present and the power switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if an hybrid control system start operation is performed, the hybrid control system does not start (the multi-information display message (smart warning light) is not displayed). However, the hybrid control system can be started by turning the power switch on (ACC) and then pressing and holding it.
  1. If there is a malfunction when the direct line is on, the hybrid control system can be started by pressing the power switch with the brake pedal released.
  2. If there is a malfunction when the direct line is off, the hybrid control system cannot be started by pressing the power switch with the brake pedal depressed.
-

WIRING DIAGRAM


B296563E06


INSPECTION PROCEDURE

HINT:
Check the connector connection to the terminal to make sure that there is no abnormality such as a loose connection, deformation, etc.

NOTICE:
  1. When using the Techstream with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and vehicle begins, or 2) connect the Techstream to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
    for Power Source Control: Body Electrical / Power Source Control / DTC.
    for Smart Key: Body Electrical / Smart Key / DTC.
  2. The smart key system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2284
Power Source Control
  1. Stop Light Switch1
ABS/VSC/TRAC
  1. Stop Light SW
-

1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. Read the Data List according to the display on the Techstream.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Specified Condition
    Stop Light Switch1
    Stop light switch1/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The hybrid control system cannot be started when this item is OFF.
    3. When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.

    OK:
    ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.



NG
Go to step 2
OK

GO TO BRAKE CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)  

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B223988E10
  1. Disconnect the G57 and G58 connector from the power management control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G57-1 (AM22) - Body ground
    Power switch off
    11 to 14 V
    G58-7 (AM21) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


3.CHECK HARNESS AND CONNECTOR (GROUND)
B223988E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G57-5 (E01) - Body ground
    Always
    Below 1 Ω
    G57-6 (E1) - Body ground
    Always
    Below 1 Ω
    G58-5 (E02) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the A65 connector from the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-23 (STP) - A65-2 (OUT)
    Always
    Below 1 Ω
    A39-23 (STP) or A65-2 (OUT) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A65 stop light switch assembly connector.



    B288689E05
  1. Disconnect the A39 connector from the power management control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A39-23 (STP) - Body ground
    Brake pedal released
    1 V or less
    Brake pedal depressed
    9 V or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)