DTC B1810/53 Short in Driver Side Squib 2nd Step Circuit |
DTC B1811/53 Open in Driver Side Squib 2nd Step Circuit |
DTC B1812/53 Short to GND in Driver Side Squib 2nd Step Circuit |
DTC B1813/53 Short to B+ in Driver Side Squib 2nd Step Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1810/53 |
|
|
| B1811/53 |
| |
| B1812/53 |
| |
| B1813/53 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check that the connectors are properly connected to the horn button assembly, spiral cable with sensor sub-assembly and airbag sensor assembly.
Disconnect the connectors from the horn button assembly, spiral cable with sensor sub-assembly and airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the spiral cable with sensor sub-assembly connector (on the horn button assembly side) is not damaged.
Check that the short springs for the instrument panel wire and spiral cable with sensor sub-assembly with the activation prevention mechanism are not deformed or damaged.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable with Sensor Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
|
| ||||
| OK | |
| 2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB 2ND STEP) |
![]() |
Connect the instrument panel wire to the airbag sensor assembly and spiral cable with sensor sub-assembly.
Connect SST (resistance 2.1 Ω) to connector E (black connector).
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect SST from connector E.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable with Sensor Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector (to Horn Button Assembly) |
| *b | Color: Black |
|
| ||||
| OK | ||
| ||
| 3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT |
![]() |
Disconnect the instrument panel wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-2 (D2+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| z5-1 (D2-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-2 (D2+) - z5-1 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-2 (D2+) - Body ground | Always | 1 MΩ or higher |
| z5-1 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-2 (D2+) - z5-1 (D2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable with Sensor Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector (to Horn Button Assembly) |
| *b | Color: Black |
|
| ||||
| OK | |
| 4.CHECK DTC |
![]() |
Connect the connectors to the horn button assembly and airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Horn Button Assembly |
| *2 | Spiral Cable with Sensor Sub-assembly |
| *3 | Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE |
![]() |
Disconnect the instrument panel wire from the spiral cable with sensor sub-assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G19-4 (D2+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| G19-3 (D2-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G19-4 (D2+) - G19-3 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G19-4 (D2+) - Body ground | Always | 1 MΩ or higher |
| G19-3 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G19-4 (D2+) - G19-3 (D2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable with Sensor Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector (to Spiral Cable with Sensor Sub-assembly) |
|
| ||||
| OK | |
| 6.CHECK SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
![]() |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-2 (D2+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| z5-1 (D2-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-2 (D2+) - z5-1 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-2 (D2+) - Body ground | Always | 1 MΩ or higher |
| z5-1 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z5-2 (D2+) - z5-1 (D2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable with Sensor Sub-assembly |
| *3 | Airbag Sensor Assembly |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector (to Horn Button Assembly) |
| *b | Color: Black |
|
| ||||
| OK | ||
| ||