DTC P0BCD-315 Generator Inverter Temperature Sensor Circuit Range / Performance |
DTC P0BD0-314 Generator Inverter Temperature Sensor Circuit Intermittent / Erratic |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0BCD | 315 | Generator inverter temperature calculated by the power management control ECU is different from the actual temperature for 10 seconds or more, and the generator inverter temperature is too high. (1 trip detection logic) |
|
| P0BD0 | 314 | Sudden change in generator inverter temperature sensor output or hunting: Generator inverter temperature is high and either of the following conditions is met:
|
| DTC No. | Data List |
| P0BCD-315 |
|
| P0BD0-314 |
|
| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| Only P0BCD-315 or P0BD0-314 is output, or DTCs other than the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
| P0A93-346 | Inverter Cooling System Performance |
| P0C73-776 | Motor Electronics Coolant Pump "A" Control Performance |
| P314A-828 | Inverter Coolant Pump Speed Signal |
Turn the ignition switch off.
|
| ||||
| A | |
| 2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR) |
Check that the service plug grip is not installed.
![]() |
Check the connector connections and contact pressure of the low voltage connectors of the inverter with converter assembly (Click here).
|
| ||||
| OK | |
| 3.CHECK QUANTITY OF HV COOLANT |
Check the HV coolant level in the inverter reserve tank.
Check for HV coolant leaks.
| Result | Proceed to |
| No leaks are found and coolant level in the inverter reserve tank assembly is above the low line. | A |
| No leaks are found and coolant level in the inverter reserve tank assembly is below the low line. | B |
| HV coolant leaks are evident. | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK COOLANT HOSE |
Check if the hoses of the cooling system are kinked or clogged.
|
| ||||
| OK | |
| 5.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE ELECTRIC COOLING FAN) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Clear DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.
Perform the "Control the Electric Cooling Fan" Active Test.
Turn the ignition switch off.
|
| ||||
| OK | |
| 6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data Ambient Temperature using the Techstream.
Check if the freeze frame data Ambient Temperature is below freezing.
| Result | Proceed to |
| Ambient Temperature value is below freezing temperature of the HV coolant. | A |
| Ambient Temperature value is above freezing temperature of the HV coolant. | B |
Turn the ignition switch off.
|
| ||||
| A | |
| 7.REPLACE HV COOLANT |
Replace the HV coolant with coolant having an appropriate concentration (appropriate freeze point) for the vehicle usage conditions (Click here).
| NEXT | ||
| ||