COOLING FAN SYSTEM > Cooling Fan Circuit |
| 1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE ELECTRIC COOLING FAN) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.
Check the operation of the cooling fan while operating them using the Techstream.
| Techstream Operation | Specified Condition |
| ON | Cooling fan operating |
| OFF | Cooling fan stopped |
| Result | Proceed to |
| OK | A |
| NG (Cooling fan does not operate) | B |
| NG (Cooling fan does not stop) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT COOLING FAN MOTOR |
Inspect the cooling fan motor (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE) |
![]() |
Disconnect the cooling fan ECU connector.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A52-1 (+B1) - A52-3 (E1) | Ignition switch ON (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Cooling Fan ECU) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU) |
Disconnect the ECM connector.
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A40-45 (RFC) or A52-2 (SI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND) |
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A52-3 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.INSPECT COOLING FAN RELAY (FAN RELAY) |
Inspect the FAN relay (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE) |
![]() |
Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (FAN relay) - Body ground | Ignition switch off | 11 to 14 V |
| *1 | No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly |
| *2 | FAN Relay |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY) |
Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A52-1 (+B1) - 5 (FAN relay) | Always | Below 1 Ω |
| A52-1 (+B1) or 5 (FAN relay) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND) |
Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (FAN relay) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FAN RELAY - NO. 1 INTEGRATION RELAY) |
Remove the FAN relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Disconnect the No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1(FAN relay) - 2C-4 | Always | Below 1 Ω |
| 1(FAN relay) or 2C-4 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU) |
Disconnect the ECM connector.
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A40-45 (RFC) - A52-2 (SI) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND) |
![]() |
Disconnect the cooling fan motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z4-1 - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected (Cooling Fan Motor) |
|
| ||||
| OK | ||
| ||