Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE

FRAME WIRE > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. REMOVE INVERTER WITH CONVERTER ASSEMBLY
(Click here).


3. REMOVE INVERTER BRACKET ASSEMBLY

CAUTION:
Wear insulated gloves.



    A268005
  1. Remove the bolt and separate the motor cable protector.



    A268006
  1. Disconnect the 2 wire harness clamps.



    A268007
  1. Remove the 2 bolts and separate the inverter reservoir tank assembly.



    A268008
  1. Remove the bolt and disconnect the earth wire.



    A268009
  1. Remove the 4 bolts and inverter bracket assembly.



4. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
(Click here)


5. REMOVE REAR SEAT CUSHION ASSEMBLY


    B297552E01
  1. Using a clip remover, disengage the 2 clips.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side



    B296114E01
  1. Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



6. REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY


    A266710
  1. Remove the 4 bolts and rear seat cushion leg sub-assembly.



7. REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT


    A266728
  1. Remove the clip and No. 1 hybrid exhaust duct.



8. REMOVE BATTERY COOLING BLOWER ASSEMBLY

NOTICE:
  1. Be sure not to touch the fan part of the battery cooling blower assemblies.
  2. Do not lift the battery cooling blower assemblies using the wire harness.



    A266759
  1. Disconnect the battery cooling blower assembly connector and clamp.



    A266760
  1. Remove the 2 bolts, nut and battery cooling blower assembly.



9. REMOVE NO. 1 HYBRID VEHICLE BATTERY COVER PANEL LH

CAUTION:
Wear insulated gloves.



    A266761E01
  1. Using the service plug grip, remove the battery cover lock striker.
    Text in Illustration 
    *1
    Service Plug Grip
    *2
    Battery Cover Lock Striker
    *3
    Button
    *a
    Projection
    *b
    Turn

    HINT:
    Insert the projection part of the service plug grip, and turn the button of the battery cover lock striker counterclockwise, and release the lock.

  1. Remove the 4 nuts and No. 1 hybrid vehicle battery cover panel LH.



10. DISCONNECT CABLE FROM POSITIVE AUXILIARY BATTERY TERMINAL


    A266722
  1. Remove the connector cover.



    A266723
  1. Remove the nut and disconnect the positive auxiliary battery terminal.



11. REMOVE FRAME WIRE

CAUTION:
Wear insulated gloves.

NOTICE:
Insulate the disconnected terminals with insulating tape.



    A266763
  1. Disconnect the connector.



    A266764E01
  1. Disconnect the 2 connectors.
    Text in Illustration 
    *1
    Shielded Wire Ground

  1. Disconnect the shielded wire ground.



    A266725
  1. Disconnect the 6 clamps.



    A266716
  1. Disengage the claw and disconnect the frame wire from the engine room junction block assembly.



    A266717
  1. Disconnect the clamp.



    A266720
  1. Disconnect the clamp.



    A266718
  1. Disconnect the clamp.



    A266719
  1. Disconnect the clamp.



  1. Remove the 3 nuts.


    A266721

  1. Disconnect the 4 clamps and remove the frame wire.

    NOTICE:
    The clamps are non-reusable parts.