DTC C1311/11 Open in Main Relay 1 Circuit |
DTC C1312/12 Short in Main Relay 1 Circuit |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| C1311/11 | 1 | Either of the following is detected:
|
|
| C1312/12 | 2 | The ABS main relay contact is turned ON (BS terminal voltage 3.5 V or more) for 4.5 seconds or more when ABS main relay OFF is requested from the ECU. |
|
| 1.PERFORM ACTIVE TEST USING TECHSTREAM (ABS MAIN RELAY) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Select the Active Test on the Techstream (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| ECB* Main Relay | ABS main relay | Relay ON/OFF | - |
Select the Data List on the Techstream (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ECB* Main Relay | ABS main relay / ON or OFF | ON: Relay on OFF: Relay off | - |
Check that the condition of the ABS main relay observed on the Techstream changes according to tester operation.
| Result | Proceed to |
| ABS main relay in the Data List turns ON/OFF using the Active Test. | A |
| ABS main relay in the Data List does not change using the Active Test. | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (BS TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-15 (BS) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Clear the DTCs (Click here).
Turn the ignition switch to ON (IG).
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1311/11 and C1312/12 are not output. | A |
| DTCs C1311/11 and/or C1312/12 are output. | B |
|
| ||||
| A | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (BI TERMINAL) |
![]() |
Turn the ignition switch off.
Check that the ABS NO. 1 (20 A) and ABS NO. 2 (10 A) fuses are normal.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-14 (BI) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (BS TERMINAL) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-15 (BS) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
|
| ||||
| OK | ||
| ||