Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1790    Center Airbag Sensor Assembly Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The airbag sensor assembly communication circuit consists of the occupant detection ECU and airbag sensor assembly.
DTC B1790 is stored when a malfunction is detected in the airbag sensor assembly communication circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1790
  1. The occupant detection ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the airbag sensor assembly communication circuit.
  2. Occupant detection ECU malfunction
  3. Airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat wire RH
  3. Occupant detection ECU
  4. Airbag sensor assembly

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1790 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C238367E07


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.
  2. In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

1.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly and occupant detection ECU. Also check that the connectors that link the front seat wire RH and floor wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly and occupant detection ECU. Also disconnect the connectors that link the front seat wire RH and floor wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)


    C238376E05
  1. Connect the connectors that link the floor wire and front seat wire RH.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Y3-7 (FSR+) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    Y3-4 (FSR-) - Body ground
    Ignition switch ON (IG)
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Occupant Detection ECU
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Occupant Detection ECU)



NG
Go to step 10
OK


3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)


    C247194E01
  1. Using a service wire, connect terminals 12 (FSR+) and 13 (FSR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Y3-7 (FSR+) - Y3-4 (FSR-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Occupant Detection ECU
    *2
    Airbag Sensor Assembly
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Occupant Detection ECU)



NG
Go to step 11
OK


4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)


    C238376E05
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Y3-7 (FSR+) - Y3-4 (FSR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Detection ECU
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Occupant Detection ECU)



NG
Go to step 12
OK


5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)


    C238376E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Y3-7 (FSR+) - Body ground
    Always
    1 MΩ or higher
    Y3-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Detection ECU
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Occupant Detection ECU)



NG
Go to step 13
OK


6.CHECK DTC
  1. Connect the connectors to the occupant detection ECU and airbag sensor assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Clear the DTCs stored in the occupant detection ECU (Click here).

  1. Clear the DTCs stored in the airbag sensor assembly (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK OCCUPANT DETECTION ECU
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Replace the occupant detection ECU with a known good one (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Clear the DTCs stored in the occupant detection ECU (Click here).

  1. Clear the DTCs stored in the airbag sensor assembly (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    Codes other than DTC B1790 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Return the occupant detection ECU that was installed for testing to its original location (Click here).



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK


8.REPLACE OCCUPANT DETECTION ECU
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Replace the occupant detection ECU with a new one (Click here).

  1. Connect the cable to the negative (-) auxiliary battery terminal.


NEXT


9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).


NEXT

END 

10.CHECK FLOOR WIRE (SHORT TO B+)


    C238378E03
  1. Disconnect the front seat wire RH connector from the floor wire.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    MY1-1 (FSR+) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    MY1-5 (FSR-) - Body ground
    Ignition switch ON (IG)
    Below 1 V

    Text in Illustration 
    *1
    Occupant Detection ECU
    *2
    Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Wire RH)



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

11.CHECK FLOOR WIRE (OPEN)


    C247195E03
  1. Disconnect the front seat wire RH connector from the floor wire.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    MY1-1 (FSR+) - MY1-5 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Occupant Detection ECU
    *2
    Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    Floor Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Seat Wire RH)



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

12.CHECK FLOOR WIRE (SHORT)


    C238378E03
  1. Disconnect the front seat wire RH connector from the floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    MY1-1 (FSR+) - MY1-5 (FSR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Detection ECU
    *2
    Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Wire RH)



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

13.CHECK FLOOR WIRE (SHORT TO GROUND)


    C238378E03
  1. Disconnect the front seat wire RH connector from the floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    MY1-1 (FSR+) - Body ground
    Always
    1 MΩ or higher
    MY1-5 (FSR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Occupant Detection ECU
    *2
    Airbag Sensor Assembly
    *3
    Front Seat Wire RH
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Wire RH)



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH