Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then displays the front passenger airbag, SRS seat cushion airbag RH and front seat belt pretensioner RH condition (activated/not activated) using the passenger airbag ON/OFF indicator.

HINT:
Approximately 6 seconds after the ignition switch is turned to ON (IG), the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the conditions listed below.


Front Passenger Seat Condition
Passenger Airbag ON/OFF Indicator
SRS Warning Light
ON Indicator
OFF Indicator
Vacant
OFF
ON
OFF
Adult is seated.
ON
OFF
OFF
Child is seated.
OFF
ON
OFF
Child restraint system is installed.
Occupant classification system failure
OFF
ON
ON

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

1.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to ON (IG), and check the SRS warning light condition.

    HINT:
    If a passenger airbag ON/OFF indicator malfunction occurs, the SRS warning light does not illuminate. If the light comes on, a DTC is stored. Troubleshoot for the DTC.

    OK:
    After the primary check period, the SRS warning light goes off.

    HINT:
    The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON (IG).



NG
GO TO AIRBAG SYSTEM (Click here)
OK


2.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).

    OK:
    "Zero Point Calibration is complete." and "Sensitivity Check is complete." are displayed.



NG
Go to step 3
OK

END 

3.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Loosen the 4 installation bolts of the front seat assembly RH.

  1. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque (Click here w/ Non-removable Headrest, Click here w/ Removable Headrest).


NEXT


4.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).

    OK:
    "Zero Point Calibration is complete." and "Sensitivity Check is complete." are displayed.



NG
Go to step 5
OK

END 

5.READ VALUE USING TECHSTREAM
  1. Using the Techstream, read Data List (Click here).

    1. Read the display when the passenger side buckle switch is operated.

      Occupant Detection 
      Tester Display
      Measurement Item / Range
      Normal Condition
      Diagnostic Note
      Passenger Buckle SW
      Passenger side buckle switch/
      Set: The seat belt is fastened
      Unset: The seat belt is not fastened
      NG: Data is not determined
      Set/Unset
      -

      OK:
      The Techstream display changes correctly in accordance with the operation of the buckle switch.



NG
Go to step 9
OK


6.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Disconnect the connectors from the occupant detection ECU and 2 rear occupant classification sensors.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


7.REPLACE OCCUPANT DETECTION ECU
  1. Connect the connectors to the 2 rear occupant classification sensors.

  1. Replace the occupant detection ECU (Click here).

  1. Connect the cable to the negative (-) auxiliary battery terminal.


NEXT


8.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).


NEXT

END 

9.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


10.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Connect the connector to the occupant detection ECU.

  1. Replace the front seat inner belt assembly RH (Click here).

  1. Connect the cable to the negative (-) auxiliary battery terminal.


NEXT


11.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).


NEXT

END