Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Front Door Courtesy Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the front door courtesy light switch using this circuit.

WIRING DIAGRAM


E235090E02


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Courtesy SW
    Front door courtesy light switch RH signal/ON or OFF
    ON: Front door RH open
    OFF: Front door RH closed
    -
    FL Door Courtesy SW
    Front door courtesy light switch LH signal/ON or OFF
    ON: Front door LH open
    OFF: Front door LH closed
    -

    OK:
    Normal conditions listed above are displayed.


    Result:

    Result
    Proceed to
    OK
    A
    Front door courtesy light switch LH or RH does not operate
    B



B
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
  1. Remove the front door courtesy light switch assembly (Click here).

  1. Inspect the front door courtesy light switch assembly (Click here).

    OK:
    Front door courtesy light switch assembly is normal.


Result:

Result
Proceed to
OK (for Front LH)
A
OK (for Front RH)
B
NG
C



B
Go to step 5

C
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-1 - 3D-36
    Always
    Below 1 Ω
    M1-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173023E16


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3D-36 - MB-2 (FLCY)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the G59 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 - G59-19 (FRCY)
    Always
    Below 1 Ω
    M2-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)