Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM

VEHICLE PROXIMITY NOTIFICATION SYSTEM > Communication between Vehicle Proximity Notification System and Diagnostic Tool is not Possible

for Preparation Click here


DESCRIPTION

The vehicle approaching speaker controller communicates with the Techstream through the DLC3.

WIRING DIAGRAM


E285125E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
The vehicle approaching speaker controller and Techstream communicate using SIL communication.

1.CHECK DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Health Check.

    Result:
    Result
    Proceed to
    Communication with the vehicle approaching speaker controller is not possible
    A
    Communication with the vehicle approaching speaker controller is possible
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - IG1 NO. 1 RELAY)
  1. Disconnect the G82 vehicle approaching speaker controller connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G82-1 (IG) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
Go to step 6
OK


3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G82-7 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - DLC3)
  1. Measure the resistance according to the value (s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G82-9 (PRST) - G4-7 (SIL)
    Always
    Below 1 Ω
    G82-9 (PRST) or G4-7 (SIL) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 7
OK


5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
  1. Measure the resistance according to the value (s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G4-4 (CG) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

6.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3A instrument panel junction block assembly connector.

  1. Measure the resistance according to the value (s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G82-1 (IG) - 3A-49
    Always
    Below 1 Ω
    G82-1 (IG) or 3A-49 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value (s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G82-9 (PRST) - 3C-16
    Always
    Below 1 Ω
    G82-9 (PRST) or 3C-16 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DLC3)
  1. Disconnect the 3A instrument panel junction block assembly connector.

  1. Measure the resistance according to the value (s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-32 - G4-7 (SIL)
    Always
    Below 1 Ω
    3A-32 or G4-7 (SIL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)