DTC B1650/32 Occupant Classification System Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1650/32 |
|
|

| 1.CHECK DTC (OCCUPANT DETECTION ECU) |
Check for DTCs of the occupant detection ECU (Click here).
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and occupant detection ECU. Also check that the connectors that link the floor wire and front seat wire RH are properly connected.
Disconnect the connectors from the airbag sensor assembly and occupant detection ECU. Also disconnect the connectors that link the floor wire and front seat wire RH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN) |
![]() |
Connect the connectors that link the floor wire and front seat wire RH.
Using a service wire, connect terminals 12 (FSR+) and 13 (FSR-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y3-7 (FSR+) - Y3-4 (FSR-) | Always | Below 1 Ω |
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *3 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y3-7 (FSR+) - Y3-4 (FSR-) | Always | 1 MΩ or higher |
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y3-7 (FSR+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| Y3-4 (FSR-) - Body ground | Ignition switch ON (IG) | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y3-7 (FSR+) - Body ground | Always | 1 MΩ or higher |
| Y3-4 (FSR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | ||
| ||
| 7.CHECK FLOOR WIRE (OPEN) |
![]() |
Disconnect the front seat wire RH from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| MY1-1 (FSR+) - MY1-5 (FSR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *3 | Front Seat Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Front Seat Wire RH) |
|
| ||||
| OK | ||
| ||
| 8.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the front seat wire RH from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| MY1-1 (FSR+) - MY1-5 (FSR-) | Always | 1 MΩ or higher |
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *3 | Front Seat Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Wire RH) |
|
| ||||
| OK | ||
| ||
| 9.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Disconnect the front seat wire RH from the floor wire.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| MY1-1 (FSR+) - Body ground | Ignition switch ON (IG) | Below 1 V |
| MY1-5 (FSR-) - Body ground | Ignition switch ON (IG) | Below 1 V |
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *3 | Front Seat Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Wire RH) |
|
| ||||
| OK | ||
| ||
| 10.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Disconnect the front seat wire RH from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| MY1-1 (FSR+) - Body ground | Always | 1 MΩ or higher |
| MY1-5 (FSR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *3 | Front Seat Wire RH |
| *4 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Wire RH) |
|
| ||||
| OK | ||
| ||