Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING

SLIDING ROOF HOUSING > INSTALLATION

for Preparation Click here



1. INSTALL SLIDING ROOF HOUSING ASSEMBLY


  1. Install the sliding roof housing assembly with the 8 bolts and 6 nuts.


    B300923E01

    Torque:
    Nut:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
    Bolt:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Install the bolts in the order shown in the illustration.

  1. Insert the sliding roof drain hose.

    HINT:
    The hose should be inserted to the base of the drain pipe.



    B300921E01
  1. Engage the claw to connect the sliding roof drain hose.
    Text in Illustration 
    *1
    Marking
    *2
    Hinge Center
    *3
    Stab

    HINT:
    1. Install the clamp by keeping sliding roof drain hose marking between stab and hinge center.
    2. Use the same procedure for the other 3 sliding roof drain hoses.



2. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B296251E01
  1. Temporarily install the curtain shield airbag assembly with the 3 hooks as shown in the illustration.

  1. Engage the hook (A).

    NOTICE:
    1. When installing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.
    2. Do not twist the curtain shield airbag assembly when installing it.



  1. Install the curtain shield airbag assembly to the body panel with a new bolt, the 4 clips, 7 new clips and 3 new spacers in the order shown in the illustration.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



    B296249E01


    Text in Illustration 
    *1
    Pin
    *2
    Clip
    *3
    Curtain Shield Airbag Assembly
    *4
    Body Panel
    *5
    Spacer
    -
    -

  1. Push in 7 new pins to each clip.

    NOTICE:
    Make sure that the pins of the clips are pushed in firmly.



    B296246E01
  1. Connect the curtain shield airbag connector.
    Text in Illustration 
    *1
    Airbag Connector
    *2
    Airbag Connector Lock

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the airbag connector lock to install the curtain shield airbag connector.



3. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL SLIDING ROOF WEATHERSTRIP


  1. Install the sliding roof weatherstrip as follows:

    1. Position the joint of the weatherstrip at the rear center.

    2. Align the alignment mark (green) on the weatherstrip with the middle marks at the corners of the sliding roof panel sub-assembly and install the weatherstrip.



    3. Install the lip of the weatherstrip firmly.


      B300939E01


      Text in Illustration 
      *1
      Joint
      *2
      Front
      *3
      Alignment Mark (Green)
      *4
      Middle Mark
      *A
      Normal
      *B
      Abnormal
      *a
      Pinched
      *b
      Exposed
      *c
      Gap (raised, wavy, etc.)
      -
      -



5. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY
  1. Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.



  1. Perform a level check.


    B300937E01


    1. Check the difference in level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass is fully closed.

      Standard:
      Area
      Measurement
      A - A
      0 + 1.0 mm (0 + 0.0394 in.)
      0 - 2.0 mm (0 - 0.0787 in.)
      B - B
      0 + 2.0 mm (0 + 0.0787 in.)
      0 - 1.0 mm (0 - 0.0394 in.)
      C - C
      0 + 1.5 mm (0 + 0.0591 in.)
      0 - 1.5 mm (0 - 0.0591 in.)
      D - D
      0 + 1.5 mm (0 + 0.0591 in.)
      0 - 1.0 mm (0 - 0.0394 in.)

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.



    B300938E01
  1. Perform a gap check.

    1. Check the gap between the roof panel and roof glass.
      Text in Illustration 
      *a
      Even

      NOTICE:
      The gap must be even all around.

  1. After adjusting the sliding roof glass, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



6. CHECK FOR WATER LEAK
  1. After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.

  1. If there are any leaks, readjust the sliding roof glass sub-assembly.



7. INSTALL SLIDING ROOF SIDE GARNISH LH


    B300918
  1. Align the front end of the garnish with the shaded portion, and then engage the 2 claws to install the sliding roof side garnish LH.



8. INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedure as for the LH side.



9. INSTALL ROOF HEADLINING ASSEMBLY
(Click here)


10. RESET SLIDING ROOF DRIVE GEAR ASSEMBLY
(Click here)


11. CHECK SLIDING ROOF SYSTEM
(Click here)


12. INSPECT FOR WATER LEAK
  1. After adjusting the sliding roof glass sub-assembly, inspect for water leaks.

  1. If there are any leaks, readjust the sliding roof glass sub-assembly.